background image

User Manual 

 

8 Appendix 

 

 

29

 

Evidence 

If  the  product  is  within  the  warranty  period,  the  customer  shall  provide  the 
product  purchase  invoice  and  date.  In  addition,  the  trademark  on  the  product 
should be legible. Otherwise,  SUNGROW has the right to refuse to honor the 
warranty. 

Conditions 

 

The unqualified products shall be disposed of by SUNGROW after 

replacement. 

 

The customer shall allow reasonable time for SUNGROW to repair the 

malfunctioning device. 

Exemption from liability 

Under the following circumstances, SUNGROW has the right to refuse to honor 
the warranty: 

 

Where the warranty period for the entire machine/module has expired. 

 

Where the device is damaged during transportation. 

 

Where the device was improperly installed, refitted, or used. 

 

Where the device is operated in extremely harsh environment as described 

in this manual. 

 

Where the fault or damage is caused by installation, repairs, modification, or 

disassembly performed by a service provider other than SUNGROW. 

 

Where the fault or damage IS caused due to the use of non-standard or 

non-SUNGROW components or software. 

 

Where the product is installed and used outside the range stipulated in 

relevant international standards. 

 

Where the damage is caused by an abnormal natural environment. 

If the product failure is caused by any of above circumstances and the customer 
requests  repair,  SUNGROW  may  provide  paid  maintenance  service  after 
judgment by SUNGROW's service department. 

Содержание PVS-18RM



































Отзывы: