Thorough Periodic Cleaning
The cooling fans draw air through the bed and will cause a dust build-
up on the lamps and reflectors. When a dust buildup is observed, it
is necessary to thoroughly clean the inside of the bench and canopy.
1 Remove the acrylic shield, metal grill and lamps.
2 With a soft cloth, wipe the entire length of each lamp.
3 Clean both sides of the acrylic shield and grill with a non-ammonia
disinfectant cleaner.
4 Wipe the reflectors with a clean damp cloth.
5 Re-install the lamps, acrylic shield and grill.
Mechanical Inspection
Inspect the unit’s mechanical integrity every 400-500 hours of use.
• Inspect the unit’s fasteners verifying that all are firmly in place. Pay
particular attention to the hinge bolts.
• Inspect gas springs for signs of wear. Replace gas springs that will not
hold the canopy in the full open position when raised.
• Inspect the AC power cord and its connections.
• Inspect the acrylic. Replace if broken, cracked or badly scratched.
Removing/Replacing Acrylic Shield (bench)
The acrylic shield in the bench and metal grill in the canopy are se-
cured in place by hinged profiles which run the length of the bed, both
front and back. Start at the end and simply
1
push the inside edge of
the profile toward the aluminum bed frame until it releases its latch-
ing action and then
2
lift. Continue to lift the profile across its entire
length until it swings back freely. Repeat for the other profile. The long
edges of the acrylic shield are now exposed. Standing in front of the
sunbed, grasp the edge of the acrylic and carefully lift it out of the
bench.
Replace the bench acrylic by laying it on the bench and pressing into
place. Close the hinged profile by pushing it back into place until it
snaps tight.
Removing/Replacing Canopy Grill
Follow the above directions for
opening the hinged profiles. As you
pry the hinged profile open the
canopy grill should start to drop
out on its own.
Using Your Sunbed
Before using your sunbed, please note the following:
• Your skin should be free of cosmetics, tanning oils, or other body
lotions prior to tanning except for those specifically made for use
with tanning devices. However, do not remove natural body oils by
bathing or showering immediately before tanning.
• Keep treated hair from contacting sunbed surfaces. Many hair prod-
ucts can damage the sunbed acrylic. Wear a shower cap or towel if
you use gels, mousses, sprays, or other hair products.
• Your sunbed is designed for individual use. Always wear the safety
goggles supplied with your sunbed or another approved pair of gog-
gles, as defined under 21 CFR 1040.20. Regular sunglasses do not
provide adequate protection from ultraviolet light.
Follow the guidelines for skin type and exposure times as shown in the
table below. Untanned persons should not tan on consecutive days
during their first week of tanning. Never tan more than once a day. Tan-
ning normally appears after the first few sessions and maximizes after
approximately four weeks. Tan once or twice per week thereafter to
maintain appearance. Persons already having a base tan may begin at
advanced levels corresponding to the extent of their base tan.
Skin Type:
I Sensitive Skin (Burns easily and severely and does not tan.)
II Light Skin
(Burns easily and severely and tans minimally.)
III Normal Skin (Burns moderately and tans average.)
IV Dark Skin
(Burns minimally, tans easily and above average.)
Operation
1 Lift the canopy, lie down on the bench
(face up), lower the canopy as close to
your body as possible.
2 Turn the timer knob clockwise to the
desired tanning session time to begin
the tanning session. The lamps will
turn on immediately.
3 When the timer reaches “0” the lamps
turn off. If you want to stop your ses-
sion before time expires, turn the timer knob back to “0”.
4 Raise the canopy by pushing the outer edge of the canopy.
Care and Maintenance
Cleaning After Use
Clean and disinfect your tanning bed’s bench and canopy after each
use. Use a non-abrasive disinfectant cleaner (such as a mixture of 2oz
of Lucasol™ disinfectant with 1 gallon of water) that does not contain
ammonia or ammonia derivatives which may damage the acrylic sur-
face. Spray the acrylic with disinfectant until thoroughly wet. Allow to
remain wet for 10 minutes and then let air dry. Wipe the canopy grill
with a soft cloth slightly dampened with disinfectant, then let air dry.
For heavily soiled areas remove the soil (lotions, etc.) using Lucas®
Spray and Wipe Tanning Bed Acrylic Cleaner. Apply solution with spray
bottle to wet the area thoroughly. Allow to remain wet for 30 seconds
and then wipe the surface dry. Then disinfect as described above.
CAUTION
Be careful. The edges of the
acrylic shield may be sharp.
PROFILE
ACRYLIC
To be assured of maximum tanning effectiveness, change lamps after
approximately 500 hours of use. Tanning will continue after this time
but at a slower rate. We recommend using the lamps specified below.
Use of uncertified lamps is a violation of Federal regulations and may
void your warranty.
1 Grasp a lamp at one end and at the middle, then turn the lamp a
quarter turn. The lamp may then be gently removed from its holder.
2 To reinstall lamp, insert pins on the ends of the lamp into the slots on
top of the lamp holder and turn the lamp a quarter turn.
The following lamps have been certified for use in this equipment:
SunFire® Plus Model F71/100W Bi-Pin
SunFire® Max Model FR71/100W Bi-Pin
RECOMMENDED EXPOSURE TIMES IN MINUTES
Level 1/Week 1
Level 2
Level 3
Level 4
Level 5
Skin Type:
1st-3rd Sessions
I Sensitive
NOT RECOMMENDED FOR TANNING
II Light
2
4
7
10
12
III Normal
3
6
9
12
12
IV Dark
4
7
10
12
12
MAXIMUM EXPOSURE TIME IS 12 MINUTES