background image

The heat pump DROPS 

D

4.1 should be installed in a room where the temperature does not drop below + 5

°

C. Where 

there is a

 

risk of the temperature drop below 5

°

C, drain the water circulation between the heat pump and the storage 

tank and blow out

 

well the installation, e.g. with compressed air.

Level  the  heat  pump  during  the  assembly  with  the  legs  of  adjustable  height.  Failure  to  comply  with  this

 

recommendation may result in a defective work and eventually damage to the equipment.

Keep away from divisions (walls ceilings etc.) for smooth maintenance work on the pump heat.

In the lower part of the pump heat housing there is a condensate discharge nozzle to which the hose outlet should be

 

connected. It is recommended to drain the condensate to the sewage system and to use a siphon.

The heat pump has a built-in automatic air vent that ensures the condenser venting and also the whole heating loop.

The pipeline between the heat pump and the storage tank must have an internal diameter of 20 mm.

On the

 

water return to the heat pump pipeline install an angled filter!!!

The pipelines should be isolated on the whole length!!!

The heat pump has two connectors for connecting the air ducts. The internal diameter of the air ducts must be min. 
200mm.
The maximum lengths of the air tubes: 8m

In case of connecting air ducts outside a building one should protect against the air circulation in the winter/ 
period of sub-zero conditions, when the heat pump is excluded from use.

Installation of the heat pump should be carried out by a person with appropriate qualifications in the field of heating and 
cooling devices.

During the installation, one should observe the health and safety regulations which applies in a given country.

3. 

Installation of Heat Pump

3.2. 

Installation recommendations

3.3. 

Connection of hydraulic circuit

3.4. 

Connection of air ducts

3.1. 

Connection of air ducts

-5-

AIR ABSORBED FROM ONE ROOM AND DISCHARGED INTO
ANOTHER ONE

AIR ABSORBED FROM THE ROOM AND DISCHARGED
OUTSIDE THROUGH THE WALL

OUTSIDE
AIR

INSIDE
ROOM

Содержание DROPS D4.1

























Отзывы: