background image

16

Sun Expert3D Graphics Card Installation Guide • September 2000

Sun Expert3D Software Package

Sun Expert3D software is delivered unbundled on a CD-ROM provided with your
installation kit.

Software Package Locations

TABLE 3-1

lists the directory locations of the Sun Expert3D software packages.

Sun Expert3D Software Package Names

TABLE 3-2

lists the Sun Expert3D software package names and descriptions.

TABLE 3-1

Location of Sun Expert3D Software Packages

Expert3D Software Packages

Directory Location

Solaris 2.6 software

/cdrom/cdrom0/Expert3D/Solaris_2.6/Product/

Solaris 7 software

/cdrom/cdrom0/Expert3D/Solaris_7/Product/

Solaris 8 software

/cdrom/cdrom0/Expert3D/Solaris_8/Product/

TABLE 3-2

Solaris 2.6, Solaris 7, and Solaris 8 Software Package Names

Package name

Description

SUNWifb.u

64-bit device driver for the PCI Bus Sun Expert3D (IFB) graphics
accelerator

SUNWifbcf

Configuration utility for the PCI Bus Sun Expert3D (IFB) graphics
accelerator

SUNWifbmn

Manual pages for the PCI Bus Sun Expert3D (IFB) graphics accelerator (not
applicable to Solaris 8 operating environment)

SUNWifbr

Boot-time device initialization support for the PCI Bus Sun Expert3D (IFB)
graphics accelerator

SUNWifbw

X server loadable module for the PCI Bus Sun Expert3D (IFB) graphics
accelerator

SUNWifbx.u

64-bit device driver for the PCI Bus Sun Expert3D (IFB) graphics
accelerator (Solaris 7 and Solaris 8 software only)

Содержание Sun Expert3D























































Отзывы: