Sun Microsystems StorEdge D2 Скачать руководство пользователя страница 40

Страница: 40 / 118

2-2

Sun StorEdge D2 Array Installation, Operation, and Service Manual • February 2002

▼

To Do Before You Begin

1. Prepare the site for the installation according to the following requirements:

■

Appendix A: “System Specifications” on page A-1

■

Appendix B: “Declaration of Conformity, Regulatory Compliance, and Safety
Statements” on page B-1

2. Unpack the array.

For an array to be installed on a desk or table top, the shipping box contains the
following items:

With an array to be installed in a cabinet, the shipping box contains the items in

TABLE 2-2

TABLE 2-1

Tabletop Array Inventory

Sun StorEdge D2 array

Two power cords

One disk drive manual

One or two SCSI cables (one for each ESM)

Two door keys

CD-ROM: Sun StorEdge D2 Array Documentation

containing the following documents in PDF

format along with the Adobe Acrobat reader:

• Sun StorEdge D2 Array Installation, Operation, and Service Manual (this manual)
• Sun StorEdge D2 Array Cabinet Installation Guide

TABLE 2-2

Rackmountable Array Inventory

Sun StorEdge D2 array with mounting tray

Two mounting brackets

16 #10-32 x 1/2 in screws

Two trim strips with four #10-14 x 7/16 in screws inserted

Four #10-14 x 7/16 in screws

Two power cords

One disk drive manual

Содержание StorEdge D2























































































































Результаты поиска

Содержание StorEdge D2

Отзывы:

Похожие инструкции для StorEdge D2

Бренды по названию

Популярные бренды

Sun Microsystems StorEdge D2, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание StorEdge D2

Отзывы:

Похожие инструкции для StorEdge D2

Бренды по названию

Популярные бренды