Sun Microsystems StorEdge D2 Скачать руководство пользователя страница 31 | Manualshive

Страница: 31 / 118

background image

Chapter 1

Sun StorEdge D2 Array Overview

1-15

summarizes the relationship between the setting of switch 1 on the ESM,

the number of ESMs, and the SCSI IDs for the disk in both single-bus and split-bus
configurations.

1.7.1.2

Disk Slot Numbers

The disk slot numbers are used by the SAF-TE commands to communicate with the
disks. In single-bus configuration, the disk slot numbers are 0 through 5 and 8
through 13. In split-bus configuration, the disk slot numbers are 0 through 5 for ESM
0 and 0 through 5 for ESM 1 because each ESM can only communicate with the six
drives associated with that ESM.

1.7.1.3

SCSI Connections

Each ESM has two independent Ultra3 SCSI bus connectors. Each ESM must be
connected by at least one SCSI cable to at least one host.

The number and configuration of the host-to-array connections depends on your
site’s storage needs. See “Supported Configurations” on page 1-19.

If the cables needed for your configuration were not ordered with the Sun StorEdge
D2 Array, contact your Sun sales representative. See the Sun StorEdge D2 Array
Release Notes for the list of supported cables.

The ESM has internal terminators for each SCSI bus connector. No external
terminators are required. Daisy-chaining from one ESM to another is not supported.
Only point-to-point SCSI connections from the host to the ESM are allowed.

The maximum SCSI bus length is 12 meters. Besides the length of the cables you use
when connecting to the host, take into account the bus length of .051 meters within
the ESM.

TABLE 1-6

Summary of Switch 1 Settings and Disk SCSI IDs

Switch 1

Configuration

Left Disk Bank SCSI ID Numbers

Right Disk Bank SCSI ID Numbers

Up

Single-bus, single ESM (in
position 0)

0, 1, 2, 3, 4, 5

8, 9, 10, 11, 12, 13

Down

Split-bus, two ESMs (in
position 0 and position 1)

8, 9, 10, 11, 12, 13
Controlled by ESM 0

8, 9, 10, 11, 12, 13
Controlled by ESM 1

«
...
29
30
31
32
33
...
»

Содержание StorEdge D2























































































































Отзывы:

Нет отзывов

Похожие инструкции для StorEdge D2

Бренд: Cutech Страницы: 2

Бренд: Data General Страницы: 91

Бренд: Quictent Страницы: 24

Бренд: VME Страницы: 2

Бренд: Keter Страницы: 28

Бренд: USP Страницы: 4

Бренд: morse Страницы: 6

Бренд: Palram Страницы: 81

Rasmus FR44-3857-6

Бренд: Palmako Страницы: 39

Бренд: G-Technology Страницы: 14

Бренд: G-Technology Страницы: 36

Бренд: Verbatim Страницы: 3

Бренд: Zte Страницы: 46

Бренд: ASUSTOR Страницы: 9

Бренд: ABSCO SHEDS Страницы: 25

Бренд: Supermicro Страницы: 126

Бренд: WiebeTech Страницы: 8

Бренд: Guardi Страницы: 19

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды