Drive Operations Menu
76
T10000 Operator’s Guide • July 2008
Revision EA
• 96174
provides details for drive operation utilities.
TABLE 4-4
Drive Operations
Options
Notes
Procedure
Drive Operation Menu
Drv Menu ?
(offline only)
If bypassed, the display advances to
the Firmware Release Level menu.
This is the entry point to the Drive
Operations submenus.
Do one of the following:
■
Press
Menu
(No) to bypass
■
Press
Select
(Yes) to enter the submenus.
Code Update Submenu
IPL FromTP
IPL From Tape, updates the drive
firmware from a code tape inserted in
the drive.
A normal data cartridge, if present,
unloads when this function is
activated.
If
CHK
xxxx
appears, try a different
code tape.
1. Do one of the following:
■
Press
Menu
to bypass
■
Press
Select
to activate.
2. When
Ld IPL Tp
appears, insert the code
tape (write-protected data cartridge that
contains the desired firmware release level
image).
Note
: When the update is done, the drive
unloads the code tape and initiates an IPL.
3. Remove the unloaded code tape.
Make Dump Tape Submenu
MakeDumpTp
Make Dump Tape specially formats
and identifies a data cartridge as a
“dump tape”; but, it does not collect
dump logs. Data cartridges used to
collect dump logs must first be
formatted this way to accept dump
logs.
A normal data cartridge, if present,
ejects when this function is activated.
If Make Dump Tape fails and
CHK
xxxx
appears, try a different data
cartridge.
1. Do one of the following:
■
Press
Menu
to bypass
■
Press
Select
to activate.
2. When
Ld Dump Tp
appears, insert a write-
enabled data cartridge.
3. When the formatted dump tape unloads,
remove the data cartridge.
4. Insert another write-enabled data cartridge, or
press
Menu
to exit the dump tape submenu.
Make Code Tape Submenu
Note: Only drives with all images loaded into the EEPROM can make code tapes.
MakeCodeTp
Make Code Tape, copies the firmware
image from the drive EEPROM to a
data cartridge. This “code tape” can
then be used to update firmware in
other drives using the Code Update
submenu.
A normal data cartridge, if present,
ejects when this function is activated.
If Make Code Tape fails and
CHK
xxxx
appears, try a different cartridge. If the
problem persists, consult your Sun
service representative.
Note:
This operation might not work
on encryption-enabled tape drives.
Note
: Make sure drive is properly prepared to
create code tapes. If required, exit Drive
Operations
Menu
and update drive to full code
of desired firmware release level.
1. Do one of the following:
■
Press
Menu
to bypass
■
Press
Select
to activate.
2. When
Ld Code Tp
appears, insert a write-
enabled data cartridge.
3. When the new code tape unloads, remove the
data cartridge, and set the write-protect
switch to lock.
4. Insert another write-enabled data cartridge, or
press
Menu
to exit the create code tape
submenu. .
Содержание StorageTek T10000
