Sun Microsystems StorageTek L40 Скачать руководство пользователя

Страница: 63 / 92

96053

Revision L

1-29

Powering-on the Library and Drives

■

Powering-on the Library and Drives

To power-on the library and drives:

CAUTION:

Possible equipment damage:

Make sure the power-on/off switch is set to

“O” before performing Step 1.

1. Close and lock the front door.

2. Attach the power cable to the power receptacle at the rear of the library and plug the

cable into an electrical outlet.

3. Press the power switch to the “

” position.

The operator status display shows the

Init in Progress:

message. When

initialization is complete, the status display shows the state of the library.

4. Use the library operator panel to configure the library and drives.

Note:

Refer to the user’s guide for any field values that you do not understand.

Note:

You must fully configure the library

before

you configure the tape

management software.

■

Recording the Configuration Information

Record your library configuration in the following table. Then make a copy of the table
and give it to the customer. The customer will refer to it when making a service call or
ordering features and upgrades.

Содержание StorageTek L40





























































































Результаты поиска

Содержание StorageTek L40

Отзывы:

Похожие инструкции для StorageTek L40

Бренды по названию

Популярные бренды

Sun Microsystems StorageTek L40, Руководство по установке

Результаты поиска

Содержание StorageTek L40

Отзывы:

Похожие инструкции для StorageTek L40

Бренды по названию

Популярные бренды