background image

Solo Pro
Ladder Treestand

PN 82065

WARNING

!

You must fully read, understand and follow these warnings 

and instructions (written and video)! Failure to follow these 

instructions may cause serious injury or death!!

You 

MUST

 also view the enclosed DVD 

BEFORE

 using your new treestand!!

WEIGHT LIMIT

SINGLE USER

300 LBS. X 1 TOTAL*

DO NOT EXCEED THIS LIMIT!

(* Includes all gear) 

Stand minimum and maximum tree size: 

8-20” diameter

Solo Pro 82065, 11/2012

• 

WHEN HUNTING FROM A TREESTAND FALLS CAUSING INJURY OR DEATH CAN OCCUR ANY TIME AFTER LEAVING THE GROUND!

  FOR 

THOSE REASONS ALWAYS USE A FALL ARREST SYSTEM (FAS) COMPRISING A FULL BODY HARNESS AT ALL TIMES AFTER LEAVING THE 

GROUND. YOU MUST STAY CONNECTED AT ALL TIMES AFTER LEAVING THE GROUND WHILE USING ANY ELEVATED HUNTING PLATFORM. 

SINGLE SAFETY BELTS AND CHEST HARNESSES ARE NO LONGER ALLOWED AND SHOULD NEVER BE USED.  IF YOU ARE NOT USING A FULL 

BODY HARNESS THAT IS PROTECTING YOU FROM A FALL, DO NOT LEAVE THE GROUND!

• 

READ AND UNDERSTAND ALL OF THE MANUFACTURER’S WARNINGS AND INSTRUCTIONS AND USE ALL SAFETY DEVICES PROVIDED.  

CONTACT SUMMIT TREESTANDS FOR ANY QUESTIONS.  FAILURE TO DO SO COULD RESULT IN INJURY OR DEATH!

• 

A SIGNAL DEVICE SUCH A MOBILE PHONE, RADIO, WHISTLE, SIGNAL FLARE OR PERSONAL LOCATOR DEVICE (PLD) MUST BE ON YOUR 

PERSON AND READILY AVAILABLE AT ALL TIMES!  ALWAYS INFORM SOMEONE OF YOUR HUNTING LOCATION, WHERE THE TREESTAND 

WILL BE LOCATED AND THE EXPECTED DURATION OF THE HUNT!

• 

DO NOT USE ANY TREESTAND UNLESS YOU ARE IN GOOD PHYSICAL SHAPE AND HAVE NO PHYSICAL LIMITATIONS OR MEDICAL 

CONDITIONS WHICH MAY PREVENT YOU FROM SAFELY USING THIS PRODUCT.  ALWAYS CONSULT A PHYSICIAN IF YOU HAVE ANY 

QUESTIONS ABOUT YOUR PHYSICAL ABILITY TO USE THIS PRODUCT.

• 

NEVER USE A TREESTAND WHILE TAKING DRUGS, ALCOHOL OR CERTAIN PRESCRIPTION DRUGS!  ALWAYS CONSULT A PHYSICIAN IF YOU 

HAVE ANY QUESTION ABOUT TAKING SPECIFIC MEDICATIONS AND USING THIS PRODUCT!

• 

NEVER USE A TREESTAND DURING INCLEMENT WEATHER SUCH AS RAIN, LIGHTNING, WINDSTORMS OR ICY CONDITIONS!  END YOUR 

HUNT AND RETURN TO THE GROUND IF ANY OF THESE INCLEMENT CONDITIONS ARISE.

• 

NEVER USE A TREESTAND WHEN FEELING ILL, NAUSEOUS, DROWSY OR DIZZY!

• 

BE WELL RESTED AND NEVER HURRY.  HURRYING CAUSES ACCIDENTS!

• 

CHECK EVERY LADDER SECTION CONNECTION EVERY TIME YOU USE THE STAND.  IF ANY LADDER SECTIONS ARE SEPARATING - DO NOT 

USE THE STAND!

• 

NEVER USE A TREESTAND ON A DEAD, LEANING, DISEASED, LOOSE BARKED TREE, ON A UTILITY POLE OR ON TREES THAT HAVE ANY 

OBSTRUCTIONS THAT MAY LIMIT TREESTAND USE!  NEVER RELY ON A TREE BRANCH FOR SUPPORT!

• 

CHECK THE GROUND UNDER THE LADDER STAND TO MAKE SURE IT IS FIRM AND LEVEL.  SLOPING GROUND  OR AN UNEVEN SURFACE 

(ONE LADDER SECTION ON A ROCK FOR EXAMPLE) CAN CAUSE YOUR STAND TO TILT OR SHIFT AS YOU CLIMB.

• 

ALWAYS MAINTAIN THREE POINTS OF CONTACT WHEN YOU CLIMB THE LADDER SECTION OF THIS STAND!

• 

NEVER JUMP OR BOUNCE ON A TREESTAND TO SECURE IT TO THE TREE!

• 

PULL UP A BOW, BACKPACK, FIREARM OR OTHER EQUIPMENT ONLY AFTER BEING SECURE IN THE TREESTAND.  FIREARMS MUST BE 

PULLED UP UNLOADED, CHAMBER OPEN AND MUZZLE DOWN!

• 

NEVER MODIFY YOUR STAND IN ANY WAY BY MAKING REPAIRS, REPLACING PARTS, OR ALTERING ADDING OR ATTACHING ANYTHING 

TO IT EXCEPT IF EXPLICITLY AUTHORIZED IN WRITING BY THE MANUFACTURER!

• 

PRACTICE INSTALLING, ADJUSTING AND USING YOUR TREESTAND AT GROUND LEVEL PRIOR TO USING IT AT ELEVATED POSITIONS!

• 

INSTRUCTIONS (WRITTEN AND VIDEO) SHOULD BE KEPT IN A SAFE PLACE AND REVIEWED AT LEAST ANNUALLY.  IT IS THE RESPONSIBILITY 

OF THE TREESTAND OWNER TO FURNISH THE COMPLETE INSTRUCTIONS TO ANY PERSON WHO BORROWS OR PURCHASES THE 

TREESTAND!  THIS SUMMIT TREESTAND IS DESIGNED TO BE USED AS A COMPLETE SYSTEM - NEVER LOAN OR SELL ONLY A PORTION OF 

THIS TREESTAND SYSTEM.

• 

BEFORE EACH USE OF YOUR SUMMIT TREESTAND, ALWAYS INSPECT THE TREESTAND AND HARNESS FOR ANY DAMAGE, CRACKS, TEARS, 

CABLE WEAR OR ABRASION THAT MAY HAVE OCCURRED IN TRANSPORTING / STORING YOUR TREESTAND.  DO NOT USE IF ANY DAMAGE 

IS FOUND!  CONTACT CUSTOMER SERVICE FOR THE APPROPRIATE REPAIR / REPLACEMENT PROCEDURE! 

• 

DO NOT LEAVE YOUR TREESTAND OUTDOORS WHEN IT IS NOT BEING USED!  ANY STAND TUBING THAT IS ALLOWED TO FILL WITH 

RAINWATER AND FREEZE WILL RUPTURE OR BURST - DO NOT USE YOUR TREESTAND IF THIS OCCURS!

© 2012 Summit Treestands, LLC
715 Summit Dr. Decatur, AL 35601
(256) 353-0634
[email protected]
www.summitstands.com

Содержание Solo Pro

























Отзывы: