manualshive.com logo in svg

SummerAire SE10I (E), Руководство по установке, Страница: 9 / 13

Поделиться
Скачать
SummerAire SE10I (E) Скачать руководство пользователя страница 9

9

SECTION VI

Fig 4

    Stage 

1 

   Stage 

2 

   Stage 

1 

+ 

2

Furnace Model

W1 BTU Output

W2 BTU Output

W1 + W2 BTU Output

Total Heat

Total Heat

Total Heat

Voltage

208

240

208

240

208

240

10kW

12975

17072

-

17072

25950

34144

15kW

25950

34144

12975

17072

38925

51216

18kW

20760

27315

25950

34144

46710

61460

20kW

25950

34144

25950

34144

51890

68288

23kW

25950

34144

33734

44387

59682

78530

27kW

25950

34144

44114

58045

70064

92190

SECTION VII

Commissioning Checklist

Ensure that

1) Fan motor shipping bracket is removed from left side of furnace.    

2) Thermostat is not connected to controller 

3) A/C condenser is connected.

4) Ground is securely connected at furnace ground lug and main panel.

5) Incoming power lines are connected and secure at main terminal block.

6) Continuous fan switch is set to off

7) Comfort max switch on furnace side panel is set to OFF.

Sequence.

1)a) Place a jumper across thermostat terminals R and W on terminal strip. Heating cycle starts and fan turns on.

   b) Allow this cycle to turn on all elements.

   c) Remove jumper. All elements turn off.

2) Place a jumper across R, Y/Y2 & G, fan starts on Cool speed and A/C starts.

3) Remove jumper, fan cycles down and A/C stops.

4) Power furnace down, connect thermostat, turn power to furnace on.

Содержание SE10I (E)














Отзывы:

Нет отзывов