6 ( 7 8 3 F R Q W L QX H G
*
+
,
-
.
6WHS
To attach Upper Hinge Bracket: repeat step 4.
6WHS
Remove Precision Fit Template. Attach Upper and Lower
Hinge Bolts on gates to the Hinge Brackets on wall (FIGURE E).
6WHS
Snap Top Latch Catch to handle on Gate Panel (
FIGURE F) and extend gate outward until Top Latch Catch is
touching the wall.
6WHS
To attach Top Latch Catch: Line gate up with wall.
Using a pencil, mark wall through top hole of Top Latch Catch
(FIGURE G). Swing gate out of the way, remove Top Latch Catch
from gate handle. Line Top Latch Catch up with mark on wall
with the top hole. Using pencil, mark wall through bottom hole
of latch. Be sure the Top Latch Catch is right side up. Place a
One-Direction Stop behind Top Latch Catch making sure that
the “protrusion” is on the stair side of the opening (FIGURE H).
1RWH
One-Direction Stops must be installed with the Latch
Catches to prevent gate from swinging both ways. Gate should
NEVER open over the stairs.
6WHS
Pre-drill hole (3/32” or 2.4mm bit), then use Phillips head
screw driver and Long Screws to attach the Top Latch Catch.
6WHS
To attach the Bottom Latch Catch: Slide the Bottom
Latch Catch into place (FIGURE I). Repeat steps 8 and 9.
6WHS
Swing Gate closed and extend Gate until handle
is engaged.
6WHS
To attach Stopper to Gate: Place Stopper on top of Gate
panel closest to hinge side. Location of Stopper should be
determined by width of Wrench head (FIGURE J).
1RWH
Stopper must be installed for one-directional stops to
function properly at top of stairs.
Be sure the door stopper is on the stairway side of the gate so the
gate cannot open over the stairs.
6WHS
Pre-drill hole (3/32” or 2.4 mm bit), then use Phillips
head screw driver and short screw to attach the Stopper to the
Gate.
6WHS
Adjust Support Foot to be gently contacting floor when
gate is closed and locked (FIGURE K).
,03257$17127(
Be certain never to allow a gap between
sides of the gate and opening or bottom of the gate and floor to
exceed 3”. Once Gate is in place, check to ensure that it is
properly secured. Hinge bolts may be extended out to
accommodate maximum extension of 48”. Once extended as
desired, lock them in place with the Wrench.
(
)
) ( $7 8 5 ( & 2 0 3 2 1 ( 1 7 6
*DWH
+LQJH%ROW
+LQJH%UDFNHWV
VKRUWORQJ
6KRUW6FUHZ
6XSSRUW)RRW
)DVWHQHUV
6 ( 7 8 3
$
6XSSRUW)RRW
$VVHPEO\
6WRSSHU
/RQJ6FUHZV
7RS
/DWFK&DWFK
:DOO$QFKRUV
2QH'LUHFWLRQ6WRSV
%RWWRP
/DWFK&DWFK
:UHQFK
$
&
'
,03257$17$WWKHWRSRIWKHODQGLQJSRVLWLRQWKHJDWHD
PLQLPXPRILQFKHVFPDZD\IURPWKHWRSVWHS
Screws are provided for mounting the brackets and latch catches
directly to wood. If mounting into wallboard, use the wall anchors
prior to using screws provided. If you are mounting the gate to
another surface, purchase and use the appropriate hardware.
1RWH
,IZDOODQFKRUVDUHQHHGHG
:
D
Pre-drill a hole in the wall (7/32” or 5.5 mm drill bit- drill and
drill bit not included).
E
Insert the wall anchors (included) into the hole with a hammer,
tap gently until the head of the wall anchor is flush with the wall.
6WHS
Attach the Support Foot Assembly to the bottom of the
Gate with the Support Foot Fasteners using the pre-drilled hole
(FIGURE A).
1RWH
If baseboard exists, use long hinge bracket on top. If there is no
baseboard, use both short hinge brackets.
6WHS
Use Precision Fit Template with Hinge Brackets on. Place
template against desired wall where gate will be located. Assure that
template is touching bottom of floor to limit gate spacing on bottom
of gate (FIGURE B).
6WHS
To attach both Hinge Brackets: Using a pencil, mark the wall
through holes of Upper and Lower Hinge Bracket (FIGURE C).
6WHS
Pre-drill hole (3/32” or 2.4 mm bit), then use Phillips head
screw driver and 2 Long Screws to attach the Lower Hinge Bracket
to the wall (FIGURE D).
+DUGZDUH.LWLQFOXGHV
Support Foot Assembly, Precision Fit Template, One-Direction Stops (2),
Hinge Brackets (3), Stopper, Top Latch Catch, Bottom Latch Catch, Support Foot Fasteners, Short Screw,
Long Screws (8), Wall Anchors (8), and Wrench.
3OHDVHFKHFNRXUZHEVLWHIRUDFFHVVRULHVDQGUHSODFHPHQWSDUWV
%
3UHFLVLRQ)LW
7HPSODWH
TOP
FLOOR
