manualshive.com logo in svg

Sullair ShopTek ST18, Руководство по эксплуатации и техническому обслуживанию, Страница: 40 / 76

Поделиться
Скачать
Sullair ShopTek ST18 Скачать руководство пользователя страница 40

6: Maintenance

ST18 & ST22 (U.S.A. & Mexico) Operation & Maintenance Manual

88291013-137 R05

34

Subject to EAR, ECCN EAR99 and related export control restrictions.

9. Reassemble and reinstall the spring cham-

ber.

10. Turn the adjusting screw clockwise until it is

under pressure from the spring.

11. Readjust the pressure regulator using inlet

modulation procedures.

6.4.11 Drive coupling maintenance

1. Shut down the compressor.
2. Mount the motor end sleeve on the motor

spindle.

3. Mount the air end sleeve on the air end shaft

so that the air end disc end contact the
shoulder of air end shaft.

4. Slide the elastomer into the discs.

• The gap between the end surfaces of the

two discs should be 2 to 3 mm.

5. Tighten the set screw on the discs.

6.5

Main motor operation and 
maintenance

• Ambient temperature 

≤

 40°C (104°F)

• Altitude 

≤

 1000 m (3280 ft)

Figure 6-6: Pressure regulator

1. Adjusting screw

7. Valve plate nut

2. Locking nut

8. Locking washer

3. Spring chamber

9. Valve plate

4. Gasket

10. Membrane

5. Spring seat

11. Bolt

6. Spring

12. Retainer ring

13. Valve body

Pressure regulator repair kit part number: 250019-453

 WARNING

Isolate the compressor from the power supply 
before making any repairs or adjustments to the 
drive coupling.

Figure 6-7: Flexible drive coupling

1. Motor end sleeve

2. Elastomer

3. Air end sleeve

Содержание ShopTek ST18













































































Отзывы:

Нет отзывов