Sulion 2171531, Быстрый старт

Страница: 7 / 11

13 12
ENGLISH ENGLISH
Calle Verano, 51 - Polígono Industrial Las Monjas -28850 Torrejón de Ardoz - Madrid (ESPAÑA)
www.sulion.es
CIF A28763647 +34 916774540 ATC: 916749481 - info@sulion.es / SAT : 916749483 - sat@sulion.es
Device technical spectifications
General
Nominal voltage and frequency 220-240V~AC 50/60Hz
Protection category Clase I
Ingress protection IP20
Work temperature -5
↔
40ºC
Maximun ceiling slope on which it can be installed 15º
Weight 5,9Kg
Power consumption in standby mode (W) <0,5
Service value measurement standard EN 62879:2020
LED
Wattage 24W
Flux 2400lm
Color temperature 3000,4000,6000K
RGB No
Data measurement 360º
Nº of ON/OFF cycles 10000
Nº of hours of lifespan 30000h
Dimmable Yes
Angle 120º
CRI >80
This product have a light source of energy efficiency class F
Fan
Speed 5
Power (W) 34
RPM 220
Airflow (m³/min) 170
Airflow (m³/h) 10200
Max noise level (dB) 35
Service value SV ((m³ / min) / W) 5
Maximum air speed (m / sec) 2,13m/s
purpose. Contact local authorities or your provider
for recycling advice. Thank you for recycling at
the collection points provided for this manual.
Note:
The important warnings and instructions
indicated in this manual are not guaranteed
to cover all possible conditions and situations
that may occur. It must be understood that common sense,
precaution, and care are factors that cannot be included in all
products. These factors can and must only be provided by the
user who maintains and enjoys this fan.
Remote control
Instructions for synchronizing the
receiver and the remote control
The control is already factory-linked with its receive.
Make sure all connections are correctly made.
Make sure that the remote control contains batteries.
Make sure that all switches (main and isolation) are on.
The control of this fan have two mode of synchronization,
Universal mode and Unit mode:
- Unit Mode:
This type of synchronization allows you to control two or
more nearby fans independently, each with its remote con-
trol.
Synchronization:
The control of this fan does not require synchronization
with the receiver, the control is already factory-linked with
its receiver
- Universal Mode:
This type of synchronization allows you to control one or
more nearby fans with the same remote control.
Synchronization:
1.-Connect the power (wall switch) of the fan or fans that
you want to control, and then just within the following
15 seconds, press the key of the remote control for 10
continuous seconds.
2.-A “beep” sound indicates that the connection has been
executed and the equipment can function normally.
3.-Now, transmitter and receiver of the fan / s will have
been synchronized. Turn off the fan / s current using the
switch or automatic and then turn it back on / s, this step
is the one that closes the synchronization process.
It is not possible for a controller to forget a fan once it has
been linked, if you want a fan to leave
to obey a command, another one must be linked to
“overwrite it”.
Preparing for installation
Note:
The estimated installation time is 120 minutes. This
product can only be installed by a certified electrician Ca-
refully separate the fan’s parts, avoiding the use of cutters
or blades that could scratch any part of it.
Remove the fan from the packaging carefully, avoiding the
use of knives which could scratch any part of it.
Remove all the components. Place the motor on a cloth or
wet surface so as not to damage its surface finish. Carefully
handle the unit to make sure that its casing does not bend
or get scratched.
The fan must be mounted on the floor or a large enough
table to prevent any component from falling off.
Timer
Nature wind
Turn off fan
Turn off light
Speeds
Change
color
temperature
Change
light
intensity
Summer /
Winter
2h 30’