Sukhoi SU-26 Скачать руководство пользователя страница 1

When it was introduced, the outstanding Russian 

SUKHOI

took the aerobatic world by storm!  Never before have

aerobatic enthusiasts had a machine so capable that it appears to have no limits.  It enables the pilot not only to exe-

cute maneuvers with exceptional precision, but allows him to invent new maneuvers, as well!  We have so completely

captured the essence of this extraordinary, competition-worthy aircraft that any good sport flyer will be able to expe-

rience the thrill of true unlimited aerobatics with his GOLDBERG SUKHOI.  

IMPORTANT: 

When selecting a power

plant for your SU-26, do not put in a larger-than-recommended engine.  This will cause undo stress to the airframe

and may result in structural failure. Remember, a bigger engine does not necessarily mean better performance.

WARNING!  THIS IS NOT A TOY!

A radio-controlled model is not a toy and is not intended for persons under 16 years old.  Keep this kit out of the

reach of younger children, as it contains parts that could be dangerous.  A radio-controlled model is capable of caus-

ing serious bodily injury and property damage.  It is the buyer's responsibility to build this kit correctly and to proper-

ly install the motor, radio, and all other equipment. Test and fly the finished model only in the presence and with the

assistance of another experienced R/C flyer.  The model must always be operated and flown using great care and

common sense, as well as in accordance with the safety standards of the Academy of Model Aeronautics (5151

Memorial Drive, Muncie, IN 47302, 1-800-435-9262).  We suggest you join the AMA and become properly insured

prior to flying this model.  Also, consult with the AMA or your local hobby dealer to find an experienced instructor in

your area.  Per the Federal Communications Commission, you are required to use only those radio frequencies spec-

ified "for Model Aircraft."

LIMITED WARRANTY

Carl Goldberg Products takes pride in the care and attention given to the manufacture of components for its model airplane kits.  The

company warrants replacement of any materials found to be defective for their intended use, prior to their use in construction of the air-

craft, provided the buyer requests such replacement within one year from the date of purchase and provided the defective part is

returned, if so requested by the company. 

No other warranty, expressed or implied, is made by the company with respect to this kit.  The buyer acknowledges and understands
that it is his responsibility to carefully construct a finished flying model airplane and to fly it safely.  The buyer hereby assumes full respon-
sibility for the risk and all liability for personal or property damage or injury arising out of the buyer's use of the components of this kit.

Pt. #2097   2/03

INSTRUCTIONS

SUKHOI SU-26

©Copyright 

1993

Содержание SU-26








































Отзывы: