Subaru ROBIN PUMP PKV401T, Инструкция по эксплуатации, Страница: 13 / 19

6
ENGLISH
FRANÇAISE
ESP
AÑOL
1. STARTING (See Fig.
3 3 3 3 3
)
(1) Open the fuel cock. (See Fig.
3
-
q
)
q
OPEN
w
CLOSE
(2) Turn the STOP SWITCH to the position “ I ” (ON).
(See Fig.
3
-
w
)
(3) Set the speed control lever 1/3 to 1/2 of the way towards
the high speed position. (See Fig.
3
-
e
)
q
Speed control lever
w
Starting position
e
High speed
r
Low speed
(4) Close the choke knob. (See Fig.
3
-
r
)
q
CLOSE
■
If the engine is cold or the ambient temperature is low,
close the choke knob fully.
■
If the engine is warm or the ambient temperature is high,
open the choke knob half-way, or keep it fully open.
(5) Pull the starter handle slowly until resistance is felt. This
is the “compression” point. Return the handle to its
original position and pull swiftly. Do not pull out the rope
all the way. After starting the engine, allow the starter
handle to return to its original position while still holding
the handle. (See Fig.
3
-
t
)
q
Recoil starter handle
w
Pull rapidly
(6) After starting the engine, gradually open choke by turning
the choke knob and finally keep it fully opened. Do not
fully open the choke knob immediately when the engine
is cold or the ambient temperature is low, because the
engine may stop. (See Fig.
3 - y )
q
OPEN
4. OPERATING YOUR PUMP
2. RUNNING (See Fig.
4 4 4 4 4
)
q
High speed position
w
Low speed position
(1) After the engine starts, set the speed control lever at the
low speed position (L) and warm it up without load for a
few minutes.
(See Fig.
4
-
q
)
(2) Gradually move the speed control lever toward the high
speed position (H) and set it at the required engine speed.
(See Fig.
4
-
w
)
■
Whenever high speed operation is not required, slow the
engine down (idle) by moving the speed control lever to
save fuel and extend engine life.
3. STOPPING (See Fig.
5 5 5 5 5
)
(1) Set the speed control lever at the low speed position and
allow the engine to run at low speed for 2 or 3 minutes
before stopping. (See Fig.
5 - q )
q
Low speed position
(2) Turn the STOP SWITCH counterclockwise to the position
“
◯ ◯ ◯ ◯ ◯
” (OFF). (See Fig. 5 -
w
)
q
ON
w
OFF
(3) Close the fuel cock. (See Fig.
5
-
e
)
q
OPEN
w
CLOSE
(4) Pull the starter handle slowly and return the handle to its
original position when resistance is felt. This operation is
necessary to prevent outside moist air from intruding
into the combustion chamber. (See Fig.
5
-
r
)
q
Recoil starter handle
※ ※ ※ ※ ※
STOPPING ENGINE WITH THE FUEL COCK
Close the fuel cock and wait for a while until the engine stops.
Avoid to let the fuel remain in the carburator over long periods,
or the passages of the carburator may become clogged with
impurities, and malfunctions may result.
5. MAINTENANCE
(See Fig.
6 6 6 6 6
)
MAINTENANCE, REPLACEMENT, OR REPAIR OF THE
EMISSION CONTROL DEVICES AND SYSTEMS MAY BE
PERFORMED BY ANY NONROAD ENGINE REPAIR
ESTABLISHMENT OR INDIVIDUAL.
1. DAILY INSPECTION
Before running the engine, check the following service items.
q
Loose or broken bolts and nuts
w
Clean air cleaner element
e
Enough clean engine oil
r
Leakage of gasoline and engine oil
t
Enough gasoline
y
Safe surroundings
u
Check the priming water
i
Excessive vibration, noise
PKV401T(US)̲PU2255.pmd 06.10.20, 8:09 PM Page 6 Adobe PageMaker 7.0J/PPC