MACHINE MAINTENANCE
Clean the rail bar every 24 hours of all excess material.
Add oil to the roller 2611-BN every 200 hours of operation.
Adjustment of Re-sharpener:
o
Always make sure the grinding stone surface is parallel to the diagonal knife
edge. Adjust the sharpener accordingly when grinding stone begins to wear out.
Replacement of Grinding Wheel:
o
Remove the Sharpener (262327) from the Motor Plate.
o
Use pliers to grip the cap end of the of the sharpener (262327) and use a W5/16
size wrench to turn the grinding wheel.
Replacement of knife:
o
Remove the Knife Guard (2633) and the Knife Cover (2633C) from the Motor
Plate (2609).
o
Remove the Sharpener (262327).
o
Attach the Wrench (2666) to the Lock Nut (2630N) and adjust until the hole on the
knife is aligned to the hole in the Motor Plate.
o
Lock the position of the knife inserting the 2.5mm Spanner (2667) into the hole
and turn the wrench counter clockwise to remove the Lock Nut.
o
Remove and switch the knife accordingly.
Replacement of Carbon Brush:
o
Use a slot drive screw driver and remove the Cap for Carbon Brush (S105) by
turning counter clockwise for both ends of the Cutting Head (260138).
o
Use a needle or sharp device to pull out the carbon brush.
o
Note: Always replace both carbon brushes on the cutting head for equal pressure
on the armature.
保養與檢修
每使用
24
小時
,
清理軌道內部之棉布絮
.
每使用
200
小時
,
請於滑輪
2611-BN
處加少許潤
滑油
.
磨刀石的調整
:
當刀片磨損時
,
將磨刀石螺絲放鬆
,
調整磨刀石位置
,
使砂輪與刀片的邊緣保持正確的接觸面
,
在
將螺絲旋緊即可
.
砂輪的更換請看圖解所示
.
刀片的更換
:
1.
將前護片
2633
及刀片護蓋
2633C
取下
.
2.
使用內六角扳手
2667
插入刀片
孔內
,
使刀片卡鎖在馬達座
2609
上
,
不會轉動
,
再使用鎖刀扳手
2666
將鎖刀螺帽
2630N
依
反時針方向轉開
.
3.
取下刀片
.
4.
裝刀片時請確定刀片上印有
“SU LEE ST-260”
字樣的一面
,
即正面朝向外面
,
人可看到
. 5.
每次更換刀片後
,
須將磨刀石
2626
重新調整至適當位置
.
碳刷的更換
:
1.
碳刷磨損太多時
,
可能損壞馬達
,
當碳刷磨損到長度剩下
5~6MM
即可更換
.
2.
只須將碳刷蓋
S105
轉開即可取出舊碳刷
,
再將新碳刷置入
,
將碳刷蓋旋上即可
. 3.
通常更
換碳刷時
,
請將左右兩個同時更換
. 4.
裝入時
,
請確認碳刷有接觸在金屬整流子上
,
勿用手碰碳
刷
.
- 5 -