background image

Model 760-03/77 User Guide 

Issue 4, October 2016 

Studio Technologies, Inc. 

Page 5

for Surround

Introduction

What This User Guide Covers

This User Guide is designed to assist  
you when installing and using the Model 
760-03 Central Controller and one or more 
associated Model 77 or Model 71 Control 
Consoles.

Overview

As creating and distributing multi-channel 
surround (5.1) and stereo audio material 
has become a day-to-day reality, the abil-
ity to simply and effectively monitor these 
sources is imperative for recording, post-
production, and broadcast facilities. And 
with audio-with-picture applications becom-
ing so prevalent, additional monitoring chal-
lenges have arisen. Studio Technologies 
has addressed these needs with the Studio-
Comm for Surround Model 760-03 Central 
Controller and the Model 77 and Model 71 
Control Consoles. With digital audio inputs, 
digital and analog monitor outputs, support 
for multiple user control surfaces, and an 
extensive set of operating resources it’s a 
simple task to integrate a monitoring system 
into virtually any facility. The carefully se-
lected group of features, including surround 
and stereo inputs, configurable input-signal 
time delay, multiple pre- and post-fader out-
puts, configurable downmix and mute/solo 
functions, and bass management, along 
with a multi-format sync input, make the 
system powerful yet simple to operate. And 
by using the best of contemporary technol-
ogy, as well as following rigorous design 
practices, the system’s audio quality is 
excellent.

A StudioComm for Surround system starts 
with the Model 77 Control Console. It’s the 
system’s “command center” and is designed 

to reside at a user’s location, allowing fin-
gertip selection of all monitoring functions. 
Numerous LED indicators provide com-
plete status information. A 4-digit numeric 
display indicates the post-fader monitor 
output level in real time. A major strength 
of the Model 77 is its ability to configure, 
under software control, many important 
operating parameters. Intended for sec-
ondary monitoring locations, the Model 71 
Control Console is a compact user control 
surface. It provides three of the most basic 
functions: a rotary level control, dim on/off 
button, and reference level on/off button.

Most installations will use only one Model 
77 Control Console. However, up to three 
additional Model 77 or Model 71 Control 
Consoles can also be connected. This 
provides multiple users with full control 
over a facility’s monitor system. And to 
make installation simple, the Model 760-03 
provides power for all connected Model 77 
or Model 71 units.

The core of this StudioComm for Surround 
system is the Model 760-03 Central Con-
troller. The one-rack-space unit contains 
circuitry that supports balanced digital 
audio inputs, balanced digital and analog 
monitor outputs, digital audio and control 
processing, and interfacing for the user 
control surface(s). The Model 760-03 pro-
vides two surround (5.1) and three stereo 
digital audio inputs. These balanced digital 
inputs are AES3-compliant; sources of this 
type are ubiquitous in many post-produc-
tion and audio facility environments. The 
inputs allow a sample rate of up to 192 
kHz and a bit depth of up to 24 to be di-
rectly supported. Circuitry associated with 
one of the stereo inputs provides sample 
rate conversion (SRC) capability, allowing 
a wide range of digital audio sources to be 
monitored. Up to 340 milliseconds of input 

Содержание 760-03
























































Отзывы: