Operation
Checking pressure setting by hand
Check the pressure setting by hand to make sure that the patient receives the proper therapy.
Perform a hand check with the patient in the worst case position, which is the side-lying position.
This position maximizes the pressure at the sacrum.
Figure 1: Under inflation
Figure 2: Proper inflation
1.
Slide your hand, palm up with fingers flat, between the product and the mattress at the
patient’s sacrum.
Notes:
•
Do not lean on the product or lift at the side as these actions can lead to false readings.
•
Adjust the pressure setpoint until you can no longer feel the patient’s sacrum.
2.
If you can feel the bony prominence (Figure 1), inflate the product.
3.
Increase the pressure up to 3mmHg by pressing the firmness button on the pump.
4.
Wait two minutes and repeat the hand check until you have adequate inflation
(Figure 2).
Note:
Check the patient at regular intervals as directed by hospital protocol.
Introduction
This manual assists you with the operation of your Stryker product. Read this manual before
operating this product. Set methods and procedures to educate and train your staff on the safe
operation or maintenance of this product.
Notes
:
•
This manual is a permanent part of the product and should remain with the product even if
the product is sold.
•
Stryker continually seeks advancements in product design and quality. This manual contains
the most current product information available at the time of printing. There may be minor
discrepancies between your product and this manual. If you have any questions, contact
Stryker Customer Service or Technical Support at 1-800-327-0770.
Product description
The Stryker Model 2790-100-000
SPR Plus
®
Overlay and Model 2863
AIR+
™ pump together
create a low air loss system to manage microclimate of heat and humidity that helps keep
moisture away from the patient’s skin. Major components of the system include the pump, hose,
hose connector, and overlay. The pump provides air to the overlay that contains micro vents to
dispel small volumes of air.
Intended use
This product is intended to assist in the prevention and treatment of pressure injuries stages
(1, 2, 3, 4, unstageable and deep tissue injury or all pressure injuries) as well as helps manage
microclimate of the patient’s skin. It is recommended to be implemented in combination with
clinical evaluation of risk factors and skin assessments made by a healthcare professional. The
product is for use by trained health care professionals. This product is for use in acute (critical
care, step down, med/surg, sub-acute, post anesthesia care unit (PACU)), or long term care
settings. This product is for single patient use.
This product is not intended to be used:
•
When spinal stability is a concern
•
To support a patient in a prone position
Contraindications
None known.
Expected life
This product has a 30 day, single patient use, expected life under normal use conditions.
Introduction
Have the lot batch code (E) available when you call Customer Service. Include the lot batch
code in all written communication.
Product illustration
A
B
C
D
E
A
Head end
C
Corner straps
E
Lot batch code
B
Hose connection
D
Foot end
Cleaning
1.
Clean the product with a clean damp cloth, soap, and water.
2.
Wipe dry.
3.
Dispose of the overlay according to your local waste management policy.
Notes:
•
Contact with disinfectant cleaners will cause degradation to the
SPR Plus
product. Avoid
disinfectants, such as solvents, alcohol based products, or Virex TB germicidal products.
•
Iodine based disinfectants will stain the product. Stains do not affect the patient or the use
of the product.
Setup the overlay
1.
Remove the product from the plastic bag. Place the product across the bed with the hose
connection on the right side of a supine patient.
2.
Stand at the foot end of the bed, unroll the cushion until you see the air valve on the right
side.
3.
Place the corner straps around the mattress cover.
4.
Make sure that the hose connection is easy to access. The air holes should face up for
airflow.
5.
Place a sheet and incontinence pad, if required, over the cushion. See
Adding or changing
linens
.
6.
Inflate the Overlay with or without the patient on the product.
Setup the pump and hose
1.
Bring the product to room temperature.
2.
Place the
AIR+
pump on the foot panel of the bed or secure location.
3.
Plug the power cord into a hospital grade outlet.
4.
Screw the pump hose connector cap to the product connector. Do not cross the threads.
5.
Select the
SPR Plus
mode on the control panel of the
AIR+
pump.
6.
Press the mmHg button on the control panel. Adjust the pressure setting as required.
Note:
See the
AIR+
pump Operations Manual for more information.
Adding or changing linens
•
Apply the linens loose to avoid a hammock effect.
•
Use minimal layers of sheeting and incontinence pads.
•
Change the linens per your hospital procedures.
Contact information
Contact Stryker Customer Service at 1-800-327-0770.
Stryker Medical
3800 E. Centre Avenue
Portage, MI 49002
USA
To view your operations or maintenance manual online, see https://techweb.stryker.com/.
Symbols
General warning
Caution
Consult instructions for use
Model number
Batch code
No sharp objects
Safe working load
1
Single patient use
Foot end
Manufacturer
Plastic #3- Polyvinyl Chloride (PVC or V)
Specifications
Safe working load
350 lb
158.8 kg
Material
Vinyl
Length
78 in.
198 cm
Width
34 in.
86 cm
Weight
6 lb
2.72 kg
Classified
Class II, not classified for protection against harmful
ingress of liquid
Compatible pump
Model 2863
AIR+
pump
Environmental conditions
Operation
Storage
Operating ambient temperature
range and humidity limits
50 F
(10 C)
0
0
104 F
(40 C)
0
0
30%
75%
Storage temperature range and
humidity limits
140 °F
(60 °C)
-40 °F
(-40 °C)
10%
95%
Stryker reserves the right to change specifications without notice.
