Stryker LIFEPAK 15 Скачать руководство пользователя страница 28

Страница: 28 / 30

Page 26

Troubleshooting Tips

For a complete list of troubleshooting tips, please

consult the LIFEPAK 15 Operating Instructions

LIFEPAK 15

Monitor/Defibrillator

Invasive Pressure (IP)

Observation

Action

Invasive pressure

value is blank

Connect the transducer to the cable and the

cable to the monitor

PX NOT ZEROED

message appears

Zero the transducer

PX ZERO FAILED

message appears

Confirm the transducer is open to air and

repeat attempt to zero

Dampened

waveform

• Check the entire system for leaks. Tighten all

connections. Replace any defective stopcocks.

• Use syringe to draw back air or particles in

catheter, then flush system

No waveform or

pressure reading

Check patient. Check stopcock positions and

monitor setup.

Invasive BP lower

than cuff BP

• Reposition transducer to correct height

• Tighten all connections

• Flush system

• Open stopcock to air and rezero transducer

Invasive BP higher

than cuff BP

• Reposition transducer to correct height

• Rezero

• Change catheter tip position

• Use mean pressure values

Inability to zero

system

• Check the stopcock position. Replace any

defective stopcocks.

• Replace transducer

Содержание LIFEPAK 15































Результаты поиска

Содержание LIFEPAK 15

Отзывы:

Бренды по названию

Популярные бренды

Stryker LIFEPAK 15, Карманный справочник

Результаты поиска

Содержание LIFEPAK 15

Отзывы:

Бренды по названию

Популярные бренды