manualshive.com logo in svg

Stryker 6086, Руководство по эксплуатации и техническому обслуживанию

Поделиться
Скачать
Stryker 6086 Скачать руководство пользователя страница 29

www.stryker.com

6086-009-001 REV B

29

Return To Table of Contents

Operation Guide

LOADING OR UNLOADING THE COT

The cot loading and unloading instructions on 

page 30

 through 

page 33 

are intended for cots that you will NOT use 

with Power-LOAD.  For Model 6086 cots with the Power-LOAD option, see the Power-LOAD Operations/Maintenance 
Manual for loading and unloading instructions.

LOADING OR UNLOADING THE COT WITH THE POWER-LOAD OPTION

The Model 6086 

Performance-PRO™ XT

 cot is fully compatible with the Model 6390 Power-LOAD system if it is 

ordered with the Power-LOAD option or compatibility kit.

For more information about using your Power-LOAD compatible cot, see the Power-LOAD Operations/Maintenance 
Manual.

 WARNING

• 

Power-LOAD is designed to be compatible with the 6085/6086 Performance-PRO XT, 6500/6506 Power-PRO XT, 
and 6510/6516 Power-PRO IT cots with the Power-LOAD option only.  In certain situations, you can use Power-
LOAD as a standard antler for most X-frame cots, but a rail clamp assembly is required for all cots without the 
Power-LOAD option. 

• 

It is the responsibility of the cot operator to ensure that the cot being used in the Stryker Model 6390 Power-LOAD 
system is a Power-LOAD compatible cot.  Injury may result if a non-compatible cot is used in the Stryker Model 
6390 Power-LOAD system.

Содержание 6086































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды