background image

Page 14 of 19 

 

The power system is designed to manage loads up to 1800 W, and extended back-up power to loads 
with total power consumption of 1440 W. To check the total power consumption of the products 
plugged into the power system, press the select button and view the output power (W) on the screen.  

To test the unit’s back-up power capabilities after installation, unplug the AC power cord to simulate a 
power outage. Ensure the products connected to the continue operating. You can test the surge 
capabilities of the Backup Power System by turning connected products on and off while the unit is 
unplugged. If products fail to operate or the screen shows an error code, see Troubleshooting.  

Run-Time on Typical Products 

AC-Powered Products 

Watts* 

How Long Will 

Power Last?* 

Home alarm system 

120 h 

Cordless phone 

120 h 

Cell phone 

120 h 

Clock radio 

66 h 

Table lamp 

35 

10.5 h 

Inkjet printer 

60 

7h 

Laptop 

75 

6 h 30 min 

13" TV 

230 

2 h 

1/2 HP Sump pump 

300 

1 h 30 min 

Microwave 

1200 

14 min 

18 ft

3

 fridge 

1500 

10 min 

*Actual power consumption as measured on sample products 

a.  Average power consumption as measured on loads tested under regular operating conditions. 

Check your appliances/devices for actual manufacturer rating since it may vary from averages 
shown here.  

b.  Run time as measured on tested loads. Run times will vary depending on actual equipment 

ratings. 

c.  The wattage listed above in the chart is only for your reference and not exact. It is not start-up 

wattage. The start-up wattage will be far higher so do not use the start-up power when the total 
power exceeds the surge power of this unit (3000W). 
 

Power Management Tips 

During a power outage, maximizing the power system run time is essential. The following suggestions 
will allow you to maximize your back-up power run time: 

Use 

Instead of 

Inkjet printer 

Laser printer 

Laptop or desktop computer with LCD monitor 

Desktop computer with CRT monitor  

Activate energy saving mode settings on computer monitor 

Bright monitor setting 

Small television 

Large television 

Small desk lamp with a low wattage bulb 

High-wattage lamp 

 

Содержание 53147




















Отзывы: