AIR FILTER
Contaminated air filters cause a reduction in engine
performance and increase fuel consumption with more
pollutants in the exhaust gas. Engines are less likely to
start readily with a contaminated air filter. Carry out the
following maintenance jobs regularly:
Before opening the
air filter, close the choke
to prevent dirt from
entering the carburetor.
Use spark plugs with resistor (thermal value 200)
under the following description:
BOSCH: WSR6F
(Original plug included, gap .015 inch)
CHAMPION: RCJ-6Y or comparable
(Replacement/
Service plug .030 inch.)
Only use spark plugs where the contact nut has been
firmly fitted. Loose connections may produce sparks,
which can cause fire. Before restarting the engine,
check the high-tension ignition cable for any damage to
it’s insulation and ensure the cable is connected
securely to the spark plug cap.
• Insert the spark plug into the cylinder head and
tighten
it.
• Push the spark plug cap firmly over the spark plug.
• Position the spark plug cover onto the housing by
aligning it with the guiding pins, push down and click
into
place.
TRANSMISSION
Transmissions are maintenance free, they require no
adding of grease or checking.
SECURING YOUR AUGER DURING TRANSPORT
With your purchase of a StrikeMaster power auger, you
have acquired one of the world’s best precision cutting
machines. A little prevention goes a long way. Whether
you transport this machine in a truck, snowmobile, ATV
or sled be sure to secure it down to prevent damage.
• Turn the wing screw
at the air filter cover
counter-clockwise.
• Flip the top of the air filter
cover forward and remove.
• Remove the fabric air filter.
• Clean the area around the filter.
Simply tapping the filter is the best cleaning method.
Never wash or clean the air filter with high compressed
air or by wetting it; never place in an oil bath or
cleaning solution.
The air filter is blocked if the engine speed noticeably
drops when the carburetor is correctly adjusted.
Under these circumstances, the filter needs replacing
(part # 20 48 154).
Low engine speed due to a blocked air filter must never
be compensated by incorrect carburetor adjustments.
This would cause severe engine failure.
Engine failure caused by incorrect care is excluded
from warranty.
• Insert the new or cleaned fabric air filter into
the
casing.
• Position the air filter lid with the lower guiding pins
onto the housing and push into place.
• Secure the filter cover by turning the wing screw
clockwise.
SPARK PLUG
Check the spark plug annually.
• Engine must be cool.
• Press the top tab of the spark
plug cover (12) down (A),
push back (B) and remove.
• Disconnect the
spark plug cap.
• Unscrew the spark plug
and dry electrodes.
The spark plug should be replaced after 50 hours of
operation or if the electrodes are badly worn.
Do not turn the engine over while the spark plug has
been removed or the spark plug cap has been
disconnected from the ignition cable. A spark may
cause a fire.
MAINTENANCE
!
!
7
12
STORAGE
!
!
Wing
Screw
Air
Filter
Because of today’s fuels STRIKEMASTER cannot
guarantee results. For summer storage or any period of
time exceeding four weeks, the following steps should
be carried out:
WET/NORMAL STORAGE :
(recommended)
• Empty fuel tank contents and dispose of properly
• Fill fuel tank to 1/4 capacity with fresh fuel,
oil and stabilizer
• Start and run engine for 2-3 minutes, varying throttle
input, then turn switch to the OFF positron
• If possible, run engine every 30 days for 2-3 minutes.
DRY STORAGE:
• Empty fuel tank contents and dispose of properly
• Fill fuel tank to 1/4 capacity with fresh fuel,
oil and stabilizer
• Start and run engine for 2-3 minutes, varying throttle
input, then turn switch to the OFF position
• Empty fuel tank contents
• Restart engine and allow engine to idle until engine
stalls (due to lack of fuel)
Suggested steps for general cleaning and storage:
• Spray WD-40 or apply oil onto the blades and blade
screws to reduce rust and corrosion
• Clean the engine thoroughly with a clean cloth
• Place a cover over engine assembly
• Store indoors in a well-ventilated low humidity area
• Store auger with blade guard attached
.030 inch
A
B
