background image

Motherboard Orientation (Optional)

Not part of the standard installation procedure, but worth noting that the 
motherboard orientation can be flipped should that provide some specific 
advantage to your planned build.

Default -               Flipped -

This is achieved by removing 4 screws which secure the back panel to the 
frame, rotating it 180 degrees, then replacing the 4 screws. In addition, 
the motherboard brackets need to be moved to the other side of the case 
in their corresponding location. This procedure will require a 2mm HEX 
screwdriver. There are some markers printed on the edge of this page 
back page that indicate the correct spacing for the motherboard brackets.

Install the Motherboard I/O Shield

Locate the I/O shield supplied with your motherboard and firmly push it in 
place from the inside of the case, making sure the orientation is correct. 
It’s important to make sure it is properly fitted otherwise the motherboard 
will be difficult to install and not align correctly with the stand-offs.

5

The spacing of the horizontal brackets does also need to be taken into 
consideration  as  the  motherboard  brackets  already  occupy  specific 
positions that might conflict with the spacing required for the hardware 
being fitted there.

The  space  above  the  motherboard  can  also  be  utilised  for  mounting 
hardware  such  as  fans,  but  due  to  the  tight  tolerances  between  the 
motherboard and frame, the brackets for this specific location must be 
installed prior to installing the motherboard.

Mounting Above the Motherboard (Optional)

HCS-M3x6

2

Содержание DA2

















Отзывы: