Strautmann Super-Vitesse CFS 3101 Скачать руководство пользователя страница 62 | Manualshive

Страница: 62 / 225

Strautmann Super-Vitesse CFS 3101 Скачать руководство пользователя страница 62

Design and function

62

Super-Vitesse CFS 3101, 3501 / Super-Vitesse CFS 3101 DO, 3501 DO 10.13

5.9.1.1 Load-sensing hydraulic system



Connect the hydraulic system only after it has been

depressurized.



Turn the tractor engine off before connecting the hydraulic

system.



Always connect the load-sensing control line when connecting

the hydraulic connector "Flow line" directly to the hydraulic pump

of the tractor.

The electro-hydraulic control block of the machine is directly connected with the hydraulic pump of the

tractor via the load-sensing control line. The current machine demand for hydraulic oil determines the

pressure and the delivery rate of the tractor's hydraulic pump.

Tractor

machine

Fig. 34

  (1)  Electro-hydraulic control block of the machine
  (2)  Load-sensing control line
  (3)  Adjustable hydraulic pump of tractor
  (4)  Hydraulic connector "Return line", connected to a free return port,

not

via control device

(5) Hydraulic connector "Flow line", directly connected to hydraulic pump of tractor, oil supply

not

via

control device

Connect load-sensing control line

1. Screw the load-sensing control line (2) into the connecting aperture (Fig. 32/2.1) of the electro-

hydraulic control block.

2. Lock the pressure regulator in the electro-hydraulic control block. For this purpose

2.1 screw the load-sensing screw (Fig. 32/2.7) in as far as it will go.

  3.  Connect the load-sensing control line (2) to the load-sensing connector of the tractor.
  4.  Connect the hydraulic connector "Return line" (4) to a free return port of the tractor.
  5.  Connect the hydraulic connector "Flow line" (5) directly to the hydraulic pump of the tractor.

Open the pressure regulator via the load-sensing screw in the electro-

hydraulic control block when the hydraulic connector "Flow line" has

been connected to the control device of the tractor. Unscrew the load-

sensing screw as far as it will go for this purpose.
Disconnect the load-sensing control line from the load-sensing

connector of the tractor before operating the machine with free

pressure regulator.

«
...
60
61
62
63
64
...
»

Содержание Super-Vitesse CFS 3101


































































































































































































































Отзывы:

Нет отзывов