Strautmann Giga-Vitesse CFS 3602 Скачать руководство пользователя страница 92

Страница: 92 / 327

Commissioning

Giga-Vitesse CFS 3602 - 4402, Giga-Vitesse CFS 3602 DO - 4402 DO 03.18

Commissioning

The following chapter provides information about the commissioning of the machine, the function and
handling of the individual components.

•

Before commissioning, the operator must have read and
understood the operating instructions.

•

Observe the information in the chapters:



"Operator's obligation"



"Training of staff"



"Warning and instruction signs"



"Safety instructions for the operator"



"Basic safety instructions"

Observance of these chapters serves your safety.

•

Only use appropriate tractors to hitch and transport the
machine.

•

Check the following adjustments when changing the tractor:



Mounting height of drawbar.



Length of propeller shaft, see information in the chapter
"Adjust length of propeller shaft to tractor".



System switch-over screw.



Setting of pressure regulator. Observe the information in
the chapter "Load-sensing hydraulic system".

Readjust if necessary.

•

Tractor and machine must comply with the national road traffic
regulations.

•

Owner (user) and driver (operator) of the vehicle are
responsible for observing the legal provisions of the national
road traffic regulations.

Содержание Giga-Vitesse CFS 3602








































































































































































































































































































































Результаты поиска

Содержание Giga-Vitesse CFS 3602

Отзывы:

Похожие инструкции для Giga-Vitesse CFS 3602

Бренды по названию

Популярные бренды

Strautmann Giga-Vitesse CFS 3602, Руководство по эксплуатации

Результаты поиска

Содержание Giga-Vitesse CFS 3602

Отзывы:

Похожие инструкции для Giga-Vitesse CFS 3602

Бренды по названию

Популярные бренды