manualshive.com logo in svg

Stratus ftServer 2900 Series, Планирование и руководство по установке

Поделиться
Скачать
Stratus ftServer 2900 Series Скачать руководство пользователя страница 23

System Documentation

Site Planning for ftServer 2900, 4900, and 6900 Systems

1-7

System Documentation 

Table 1-2

 lists the hardware documents for ftServer 2900, 4900, and 6900 systems, 

and the tasks described in each document. Also see 

Table 1-3

 (for Windows-based 

systems) 

Table 1-4

 (for Linux-based systems), or 

Table 1-5

 (for VMware 

vSphere-based systems).

Table 1-2. ftServer 2900, 4900, and 6900 System Documentation

Document

Task

Stratus ActiveService Network 
Configuration Guide

(R072)

Configure your system for support by the ASN 

Stratus ftServer Systems: PCI Adapter 
Guide

(R461)

Install, configure, replace, or troubleshoot PCI adapters 

Stratus ftServer Systems: Technical 
Reference Guide

(R550)

Consult technical reference information for ftServer systems

View or change BIOS settings in the system BIOS setup 
utility 

Use the Unified Extensible Firmware Interface (UEFI)
to configure the BMC and configure user accounts

Stratus ftServer Virtual Technician 
Module User’s Guide

 (R642)

Use the VTM console to remotely control, monitor, and 
troubleshoot your system

Read Me First: Unpacking ftServer 
Systems

(R784)

Inspect and unpack ftServer system hardware that you 
install in your cabinet

Stratus ftServer 29x0, 49x0, and 69x0 
Systems: Operation and Maintenance 
Guide

(R785)

Start up, shut down, and operate your system 

Troubleshoot system hardware 

Remove and replace CRUs, including PCI adapters 

ftScalable Storage G3: Getting Started 
Guide

(R687) 

Install and initially configure an ftScalable Storage G3 
system

Perform site-planning tasks for an ftScalable Storage G3 
system

Using ftScalable Storage G4 
Systems

(R789)

Install and initially configure an ftScalable Storage G4 
system

Содержание ftServer 2900 Series





















































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды