Stratco Outback Clearspan Gable Скачать руководство пользователя страница 1 | Manualshive

Страница: 1 / 16

background image

INSTALLATION

GUIDE

• Drill
• Hex Head Adaptors (5/16 & 3/8)
• Phillips Head Adaptors (5/16 & 3/8)
• Rivet Gun
• Tape Measure
• Tin Snips
• Spirit Level
• Hack-Saw

• Post Hole Digger
• Silicone Gun
• Spanner or Ratchet
• Adjustable Construction Props
• Turn Up/Down Tool
• Concrete
• Ladder
• Extended Drill bit

It is important to check your Local Government Authority requirements before the installation of your new Stratco Outback

®

Clearspan Gable. It

is the builder’s responsibility to ensure any existing structure that an Outback Clearspan Gable is being attached to is adequately reinforced to

accommodate the additional loads imposed by the verandah, patio or carport. Read these instructions thoroughly before starting your project
and refer to them constantly during each stage of construction. Contact Stratco for advice if you do not have the necessary tools or information.

Before starting, lay out the main components in order of assembly on the ground and check them against the delivery note. The ‘Components’

section identifies each part of your Outback Clearspan Gable with Cooldek and shows the relative location of the components.

Mark out the overall area of your verandah, patio or carport and ensure that it is free from obstructions. Beam to wall connections can cause

difficulty if they coincide with door and window openings, so avoid these in your design. Ensure there is reasonable access for materials and

working space and consider the disposal of run-off water. Check the column and beam positions on the ground; roughly check they are square
by measuring the diagonals, then mark out the column locations. If columns are to be ‘in ground’, dig the holes to Stratco specifications.

BEFORE YOU START

The Outback kit does not include fixings to attach the unit to an existing structure or concrete/masonry anchors for the column installation.
Other items not included in the standard kit are infill panels and accessories, box gutters and cover flashings. If required, they must be
purchased as additional items.

ADDITIONAL MATERIALS

ADDITIONAL MATERIALS

Outback Clearspan Gable

WITH COOLDEK ROOFING

®

®

1
2
3
...
»

Содержание Outback Clearspan Gable

















Отзывы:

Нет отзывов

Похожие инструкции для Outback Clearspan Gable

Бренд: GAGGIO Страницы: 2

Resort Elite PY72 B Series

Бренд: Baby Trend Страницы: 34

Бренд: Century Страницы: 12

Бренд: Graco Страницы: 21

NORDIC 01 02 51 Series

Бренд: Quax Страницы: 17

Бренд: KIDWELL Страницы: 44

Бренд: Bellamy Страницы: 11

Бренд: Coleman Страницы: 2

allen+roth ASPEN GROVE 4PC CHAT FZS60569S

Бренд: LF Страницы: 2

Бренд: Plum Страницы: 28

Бренд: Plum Страницы: 28

Trama NEST 07507

Бренд: Bebecar Страницы: 40

Бренд: Bebecar Страницы: 36

Бренд: BEBE CONFORT Страницы: 60

Бренд: BabyGo Страницы: 14

Бренд: RH Baby&child Страницы: 6

JEUNE FRENCH 1079-13

Бренд: RH Baby&child Страницы: 13

ACTIVITY BOUNCER

Бренд: Banzai Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды