Stratasys uPrint Скачать руководство пользователя страница 81

Страница: 81 / 383

4-34

Hard Drive

Required Tools

•

⁄

” nut driver or standard screwdriver.

• Phillips

screwdriver

Hardware

• 6-32

⁄

” Phillips pan head screws (x8)

Removing the SATA Hard Drive

Open the electronics bay. See

Opening the electronics bay on page

4-15.

Touch the metal plate of the electronics bay cover to discharge any static electricity.

Disconnect the power input cable by pressing the metal tab in and pulling down. See

Figure 4-59.

Figure 4-59: Hard drive power cable location

Disconnect the SATA cable by pressing the metal tab in and pulling down. See

Figure 4-

60.

Disconnect the

power input cable

Содержание uPrint
































































































































































































































































































































































































Результаты поиска

Содержание uPrint

Отзывы:

Stratasys uPrint, Руководство по обслуживанию, Страница: 81 / 383

Результаты поиска

Содержание uPrint

Отзывы: