Stratasys uPrint Скачать руководство пользователя страница 248

Страница: 248 / 383

uPrint/uPrint SE Service Manual

5-39

Figure 5-356: X-Drive Belt Tension Adjustment

Remove the belt fixture and run the head back and forth several times.

Continue to adjust and check the tension until the tension meets specification.

Reinstall side and top panels.

Checking/Adjusting the Y-Drive Belt Tension

Remove the top, side and side access panels.

If required, allow system to cool to room temperature (approximately 20 minutes).

Move the Head Assembly to full rear travel within the build envelope

Position the dial indicator on the top section of the Y-Drive belt at the center point of the

belt. See

Figure 5-357.

Figure 5-357: Y-Drive Belt Tension Check

Note:

The Y-Drive system consists of two drive belts - one on each side of the

build envelope. Each belt must be checked, adjusted and of equal values.

X belt tension

bolt

Dial Indicator position for Y-Drive belt tension check.

Y-Drive Belt clamp (one on each side).

Содержание uPrint
































































































































































































































































































































































































Результаты поиска

Содержание uPrint

Отзывы:

Stratasys uPrint, Руководство по обслуживанию, Страница: 248 / 383

Результаты поиска

Содержание uPrint

Отзывы: