background image

Scan here to register your product

Warranty  does  not  cover  pre

-

delivery  service 

and adjustment, or failure that may occur as a result of 

lack of/ incorrect pre delivery service and adjustment.

Warranty  does  not  cover  any  incidental,  indirect  or 

consequential  loss,  damage  or  expense  that  may  result 

from any defect, failure or malfunction of a product.

Should  any  issue  be  found  to  be  a  combination  of  a 

warranty  failure  and  a  non-warranty  issue,  the  repair 

cost  component  to  rectify  and  repair  the  non-warranty 

failure is the customers’ full responsibility.

The  decision  that  an  issue  with  a  product  qualifies  as 

a  warranty  claim  is  made  at  the  sole  jurisdiction  of 

Euroquip.

No  costs  incurred  will  be  considered  under  warranty  if 

repairs are carried out by a party other than a Euroquip 

Approved  Service  Agent,  unless  with  prior  consent  in 

writing from Euroquip. 

It  is  the  responsibility  of  the  purchaser  to  deliver  a 

prod-uct  under  warranty  to  the  nearest  relevant  service 

agent  or  product  reseller.  Warranty  does  not  cover  call 

outs, mileage and freight costs. 

If a product is repaired under warranty, parts and labour 

required  for  the  repair  will  be  supplied  at  no  charge. 

Warranty  assessment  and  repair  will  be  scheduled  and 

executed  ac-cording  to  the  normal  work  flow  at  the 

service  location  and  depending  on  the  availability  of 

suitable replacement parts.

This  warranty  policy  is  an  additional  benefit  and  does 

not affect  the  legal  rights  of  any  end  user,  reseller  or 

service agent.

Warranty

As  part  of  an  on-going  commitment  to  excellence  in 

product  support,  Euroquip  offers  a  comprehensive 

product warranty program.

In  order  to  qualify  for  full  warranty  support,  your 

product  must  be  registered. Product  not  registered with 

Euroquip is supported by a base 12 month warranty only. 

Spare parts and  technical  support  will  not  be  available 

for  an  unreg-istered  product  outside  of  this  base 

warranty  period.  If  a  Euroquip  dealer  has  not  already 

registered  your  product,  please  register  it  online  or 

download 

physical 

registration  form 

at 

www.euroquip.co.nz.

Registered warranty period for the EZITIG 205DC:

Commercial Use:  24 Months 
Domestic Use:   24 Months

Warranty  covers  failure  caused  by  manufacturing  and 

ma-terial  defects  in  the  product,  during  the  warranty 

period  specified.  The  warranty  period  begins  when  the 

product is purchased  by  the  end  user.  Warranty  is  not 

transferrable  and  is  only  claimable  by  the  original 

purchaser.

Warranty does not cover parts that are subject to wear 

and tear from usage.

Warranty  covers  failure  of  a  product  caused  by 

defective materials  and/or  manufacturing  for  the  period 

given  and  the  usage  specified  by  Euroquip.   The 

warranty  period begins  when  the  product  is  purchased 

by  the  end  user.  Warranty  is  not  transferrable  and  is 

only claimable by the original purchaser. 

Warranty  also  does  not  cover  failure  caused  by  the 

untimely  replacement  or  service  of  the  above  wearing 

parts. Evi-dence  must  be  provided  that  the  product  has 

been  main-tained  and  serviced  suitably  for  a  claim  to 

be considered under warranty.

Failure  caused  by  incorrect  operation  of  the  product, 

lack  of  proper  care  and  maintenance  of  the  product, 

external  damage,  external  circumstances  such  as 

contaminated fuel or poor water supply, modifications to 

the  product,  attempted  repair/  service  by  a  party  other 

than  an  Approved  Service  Agent,  is  not  covered  under 

warranty.

http://www.euroquip.co.nz/Us/Product

+RegisForm.html

49

www.strata.co.nz

EZITIG 205DC

Содержание EZITIG 205DC





















































Отзывы: