Störk-Tronic 900350.053 Скачать руководство пользователя страница 12

Страница: 12 / 12

Order number: 900350.053 V2.73

Page 12

Technical data

Analogue inputs

F1:

Temperature sensor Pt100 or thermocouple TC

Measuring range: Pt100

-80...+400 °C

-50...+400

°C

Measuring accuracy referred to controller at 25 C: +/-0.5 K and +/-0.5 % of measuring range

Digital inputs

E1:

External start-stop button

E2:

Overtemperature signal contact from temperature limiter

Switching outputs

K1:

Relay, 8(1.5) A / 250 V~, normally-open contact (heating contact)

K2:

Relay, 8(1.5) A / 250 V~, normally-open (control contact 2)

K3:

Relay, 8(1.5) A / 250 V~, normally-open (raise basket)

K4:

Relay, 8(1.5) A / 250 V~, normally-open (lower basket)

K7:

Relay, 8(1.5) A / 250 V~, change-over contact (alarm contact)

S2:

Linear analog output with 0 to 20 mA output range

PWM output

S1:

PWM output 3.6 KHz, output of PID correcting variable for control via a fan

Power supply

100 ... 240 V~ 50/60 Hz

Connectors

Screw terminals, grid 5.00 mm, for cables up to 2.5 mm²

Ambient conditions

Storage temperature

-20...+70 °C

Operating temperature

0...55 °C

Relative humidity

max. 75 % r.H., no condensation

Weight

approx. 600 g

Enclosure type

IP65 front, IP00 rear

Protection class

Protection class II, rated voltage 250 V~

Interface

Shielded 2-wire cable, twisted pair, maximum cable length 1000 m
Interface driver: RS485, galvanically not isolated.
The network must be designed in line topology with termination resistor of 120 Ohm on both sides.

Installation data

The display unit is designed for installation in a switching panel (note dimensioned drawing).
Front size:

154.8mm x 61.8mm

Assembly size:

180 x 87mm

Assembly depth: approx. 25mm

7,3

154,8

180

61,8

62,1

155,2

172

Содержание 900350.053













Результаты поиска

Содержание 900350.053

Отзывы:

Бренды по названию

Популярные бренды

Störk-Tronic 900350.053, Руководство пользователя

Результаты поиска

Содержание 900350.053

Отзывы:

Бренды по названию

Популярные бренды