background image

1. 

Lay down the doors with the sheets attached.

2. 

Cap the sheets with the 3000mm channels 

F

.

3. 

Use the door spacers 

I

 to make sure the door fits the gap 

 

(they sit on top of the “Z” door jambs 

L

). (see diagram 1).

4. 

Drill and fix (rivet or screw) the channels at every second rib down 

through the top.

5. 

Attach the door spacers at each end through the “Z” door jambs 

and channels.

6. 

Put three fixings underneath through the channels into the 

sheeting pan and the top and bottom of the door spacers and “Z” 

door jambs (see diagram 1).

7. 

Fit the padbolt to the door strap on the outside of the door using 

wide flange rivets or screws.

Tips

•  Put the padbolt on the door before 

erecting the panels. It will stop the door 

swinging around!

diagram 1

Channels will come short of 
the ends of the sheeting by 
10-15mm on all panels.

Fix through the top and 
bottom of the channels into 
the door jamb and spacer. 
The door jamb goes on 
inside of the channel.

The higher side of the 
channel goes to the inside of 
the shed. It is very important 

to include the fixings on the 

underside of all the channels 
as they are structural (except 
the roof channels).

inside

outside

spacer

channel

Padlock keeper assembly

keeper

washer

rivet

If you choose to vary from these instructions 

your warranty will be impaired.

3

Step 3: 

Front wall

I

N

F

2 x 3000mm “U” channels. 
2 x 1586mm door spacers.
padbolt

Note:
The channel cutouts:
1 sided cutout to BOTTOM
2 sided cutout to the TOP

You will need:

I

I

N

L

F

If you need advice, call us FREE on 0800 807 433  

or email us at [email protected]

Содержание rite on









Отзывы: