background image

6600 Lumen LED

Weatherproof 4 ft.

Ceiling Light

MODEL No: WWL4-6600N

PACKAGE CONTENTS

INSTALLATION (CONTINUED)

ADDITIONAL WARNINGS

3 YEAR LIMITED WARRANTY

This product is guaranteed against failure due to factory defects in materials or workmanship for three (3) years from the date of 

purchase. This warranty is non-transferable and applies only to the original owner. Proof of purchase is required for repair or 

replacement. This warranty does not cover normal wear of parts or damage resulting from any misuse of the product. Misuse of 

the product includes, but is not limited to: washing the product, using in extreme weather conditions, opening the product, or 

trying to remodel the product. Important: this warranty is only valid if the product has been purchased through an authorized 

reseller.

WARNINGS 

WARNING: Do NOT look directly at LED light sources.

This fixture is IP66 rated and therefore is suitable for wet 

location indoor /outdoor use.

WARNING: Use only in 100-277VAC, 60Hz circuits.

WARNING: TO AVOID ELECTRIC SHOCK,

DISCONNECT POWER BEFORE INSTALLING

SAFETY AND PRECAUTIONS

1. Suitable for indoor/outdoor use.

2.   Do  NOT install over stoves.

3. Do NOT look directly at LED light sources. 

4.  The LED modules used in this fixture are not serviceable.

5. This product is inspected prior to shipping. Do not use if product is cracked, broken or missing parts.

6. Suitable for use in operating environments ranging between  -4° to 122°F (-20° to 50° C). 

7. Electrical requirements can be found on back of the fixture.

8. If unsure how to install a light fixture, call a qualified electrician.

•  Shut off power to electrical outlet before installing or servicing this fixture.

CUSTOMER SERVICE 

For questions regarding this product, please contact us at 303.652.6164, M-F 7am - 4pm MT or e-mail us at 
[email protected].

This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful 

interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Warning: 

Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate 

the equipment. The user is cautioned that any changes or modifications not expressly approved by the party responsible for compliance could 

void the user’s authority to operate the equipment. Note: This equipment has been tested and found to comply with the limits for a Class B 

digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a 

residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with 

the instructions, may cause harmful interference to radio communications. However, there is no guarantee that the interference will not occur in 

a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning 

the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: 1) Reorient or 

relocate the receiving antenna. 2) Increase the separation between the equipment and receiver. 3) Connect the equipment into an outlet on a 

circuit different from that of the receiver. 4) Consult the dealer or an experienced radio/TV technician for help.

Electrical requirements can be found on fixture. 

Use with a minimum 90° C supply conductors.

Revision Date: 09-20-2017

TROUBLESHOOTING GUIDE

CLEANING INSTRUCTIONS

Disconnect power to fixture before cleaning. Using a soft cloth, clean the fixture using a mild, non-abrasive glass cleaner. DO 

NOT use solvents. DO NOT use cleaners containing abrasive agents. NEVER spray liquid cleaner directly onto the LEDs, fixture 

or wiring. 

Before starting work to connect the fixture, shut off power supply at the circuit breaker panel to avoid electrical shock.

1.69 in.

4,3 cm

 WARNING: DO NOT alter or disassemble the fixture it is 

completely enclosed and does not contain replaceable or 

serviceable parts.

DIMMING

• DO NOT USE THIS FIXTURE WITH DIMMERS.
Doing so will void the warranty of this product.

Product Facts:
Color Temperature: 4000K
Lumens: 6600 LM
Lumen Efficacy: 143
Input Voltage: AC120/60Hz
Rated Watts: 46W
CRI: 80
Power Factor: 0.9
LED Beam Angle: 120°
LED Emitter Life: 50,000 hours
Operating Voltage: 100-277v
Operating Temperature: -4° to 122°F (-20° to 50° C)
Cord: 18/2 SJT
Cord Length:1.5 ft

1

4

3

2

3. Move the fixture up to the mounting 

clips (Fig. 10). Hook one side of the 

mounting track to both mounting clips 

(Fig. 11) and push the fixture up (Fig. 

12) until the mounting clip track snaps 

into the mounting clips (Fig. 13). 

48 in.

122 cm

CAUTION: Personal injury can occur, along with damage  

to the fixture and/or mounting surface may result if the 

fixture is pulled from the surface. To prevent premature failure 

from overheating, fixture should only be installed in 

environments where the operating temperatures are between  

-4° to 122°F (-20° to 50° C). 

WARNING: This product may represent a possible shock or  

fire hazard if improperly installed or mounted. Products should 

be installed following these instructions, local electrical codes and/or 

the current National Electric Code (NEC).

Fig. 11

Fig. 12

Fig. 13

Fig. 6

2.9 in.

7,3 cm

       WARNING: DO NOT install lights within 10 feet of a pool, 

spa or fountain.

WARNING: This product needs to be grounded properly in a

manner consistent with local electrical codes and/or the 

current National Electric Code (NEC). If the installer cannot 

determine if this product is properly grounded, has no ground wire, 

or is unfamiliar with electrical wiring methods of properly 

grounding fixture, consult a qualified electrician.

         WARNING: Avoid using this product in the immediate vicinity of 

         highly flammable materials, liquids and gases.

INSTALLATION INSTRUCTIONS

2x Medium

     Screws

2x Mounting

     Clips

2x Wall

 Anchors

INSTALLATION (CONTINUED)

Fixture does not turn on.

Problem

Probable Cause

Solution

Circuit breaker trips or fuse blows

when light is turned on.

1. Bad connection.

2. Faulty switch.

3. Power is off.

1. Discontinue use

    immediately.

1. Check wiring connections.

2. Test switch or replace it.

3. Verify power supply is on.

1. Call customer service at 303.652.6164.
2. Call an electrician.

BACK

SIDE

 Mounting Clip Track

16” Insulated 
Direct Wire Cord

Diffuser

1. Each mounting clip attaches approximately 4 inches from each end of the fixture on the mounting clip track (Fig. 2). Locate where 

each mounting clip will be mounted and mark the location on the mounting surface (Fig. 3)

Fig. 2

Fig. 3

Drywall installation:

With a 3/16 in. drill bit, drill holes
for both anchors (included) at the 
marked installation locations (Fig. 

5). Insert each anchor into the 
pre-drilled holes (Fig. 6). Fasten 
the mounting clips into place 
with the included screws (Fig. 7)
Snap light into clips.

Wood Surface Mount:

Using a 1/8 in. drill bit, drill pilot
holes for both screws (included) 
at the predetermined installation 
location (Fig. 8). Fasten the 
mounting clips into place with 
the included screws (Fig. 9)
Snap light into clips.

Fig. 5

Fig. 6

Fig. 7

Fig. 8

Fig. 9

Fig. 10

2. Mounting Clips can be mounted to wood or drywall. 

4”

4”

Before beginning, disconnect the power to the junction box. If replacing an existing fixture with more than two wire 

leads, make a note as to where they were connected.

Fig. 1

1. Disconnect the power to the junction box. Attach the direct wire 
cord to a junction box, use wire nuts to connect the black wire 
from the direct wire cord to the black power supply wire (Live
from the junction box and the white wire from the direct wire cord 
to the white power supply wire (Neutral) from the junction box 

(Fig. 1). After making the connections, carefully push the excess wiring 
inside the junction box.

3. Your installation is now complete (Fig. 14). Restore the power.

Fig. 14

Отзывы: