Stone 45CM Скачать руководство пользователя страница 17

Страница: 17 / 20

- 17 -

MAINTENANCE SCHEDULE

45CM & 55CM

A. ENGINE

- Daily check the oil

levels in the engine and engine

reduction unit. The engine warranty

VOID

if run without oil . Since

there are many options available on

this mixer, consult the ENGINE

MANUAL for specific

recommendation as to oil level, oil

type required and frequency of oil

changes required. For maximum

service life from the engine, follow

those recommendations.

B. WEEKLY

- Grease trunnions (2)

places.

C. MONTHLY

- Grease drum

spindle through grease fitting (1)

place.

YEARLY

- Disassemble drum and

drum spindle and clean and repack

drum spindle bearings as follows -

Remove plug from inside drum.

Remove the cotter key and castle

nut from the drum spindle and slide

the drum of the spindle.

Remove the drum bearings, clean

thoroughly and repack with grease.

Clean spindle and drum bearing

housing and coat with grease inside.

Reassemble the drum and bearings

to the drum spindle and install the

castle nut to hold in place. Tighten

castle nut snugly to seat bearings,

then back off to the nearest slot

which aligns with the hole in the

spindle shaft, then install cotter key.

Turn drum and check that it turns

freely. Install plug and tighten

securely.

Note:

DO NOT allow any

sand, cement or other foreign

matter to fall into the bearing

housing during reassembly.

NOTE:

Cowl removed for clarity.

Do not operate mixer with cowl

removed.

D. YEARLY

- Disassemble the

wheel hubs and clean and repack

the wheel bearings with grease.

Reassemble the hubs using new

wheel seals. Tighten castle nuts

snugly then back off to the 1st slot

that aligns with the hole in the axle

spindle. Install cotter key and spin

hubs to check for binding or

excessive slop. Reinstall dust cap

and tires. DO NOT lubricate pinion

and ring gear. They will collect

abrasive materials and accelerate

wear.

Use any Grade #1 lithium base

grease for the above applications.

BELT TENSION

WEEKLY -

Check drive belt for

proper tension and excessive wear.

Replace worn belt or adjust belt

tension as required. To remove and

adjust belt, loosen (do not remove)

motor base mounting bolt, lift up on

motor base, and remove belt.

Install new belt and push motor

base down until proper belt tension

is achieved. Tighten motor base

mounting bolt. Proper belt tension

is achieved when belt deflection is

1/2 inch to 3/4 inch midway

between drive sheaves.

Содержание 45CM





















Результаты поиска

Содержание 45CM

Отзывы:

Бренды по названию

Популярные бренды

Stone 45CM, Руководство оператора

Результаты поиска

Содержание 45CM

Отзывы:

Бренды по названию

Популярные бренды