manualshive.com logo in svg

STMicroelectronics STM32F405, Справочное руководство


Поделиться
Скачать
background image

Memory and bus architecture

RM0090

68/1731

DocID018909 Rev 11

2.3.1 Embedded 

SRAM

The STM32F405xx/07xx and STM32F415xx/17xx feature 4 Kbytes of backup SRAM (see 

Section 5.1.2: Battery backup domain

) plus 192 Kbytes of system SRAM.

The STM32F42xxx and STM32F43xxx feature 4 Kbytes of backup SRAM (see 

Section 5.1.2: Battery backup domain

) plus 256 Kbytes of system SRAM.

The embedded SRAM can be accessed as bytes, half-words (16 bits) or full words (32 bits). 
Read and write operations are performed at CPU speed with 0 wait state. The embedded 
SRAM is divided into up to three blocks:

•

SRAM1 and SRAM2 mapped at address 0x2000 0000 and accessible by all AHB 
masters.

•

SRAM3 (available on STM32F42xxx and STM32F43xxx) mapped at address 
0x2002 0000 and accessible by all AHB masters. 

•

CCM (core coupled memory) mapped at address 0x1000 0000 and accessible only by 
the CPU through the D-bus.

The AHB masters support concurrent SRAM accesses (from the Ethernet or the USB OTG 
HS): for instance, the Ethernet MAC can read/write from/to SRAM2 while the CPU is 
reading/writing from/to SRAM1 or SRAM3.

The CPU can access the SRAM1, SRAM2, and SRAM3 through the System Bus or through 
the I-Code/D-Code buses when boot from SRAM is selected or when physical remap is 
selected (

Section 9.2.1: SYSCFG memory remap register (SYSCFG_MEMRMP)

 

in the 

SYSCFG controller). To get the max performance on SRAM execution, physical remap 
should be selected (boot or software selection).

2.3.2 Flash 

memory 

overview

The Flash memory interface manages CPU AHB I-Code and D-Code accesses to the Flash 
memory. It implements the erase and program Flash memory operations and the read and 
write protection mechanisms. It accelerates code execution with a system of instruction 
prefetch and cache lines.

The Flash memory is organized as follows:

•

A main memory block divided into sectors.

•

System memory from which the device boots in System memory boot mode

•

512 OTP (one-time programmable) bytes for user data.

•

Option bytes to configure read and write protection, BOR level, watchdog 
software/hardware and reset when the device is in Standby or Stop mode.

Refer to 

Section 3: Embedded Flash memory interface

 

for more details.

2.3.3 Bit 

banding

The Cortex

®

-M4 with FPU memory map includes two bit-band regions. These regions map 

each word in an alias region of memory to a bit in a bit-band region of memory. Writing to a 
word in the alias region has the same effect as a read-modify-write operation on the 
targeted bit in the bit-band region.

In the STM32F4xx devices both the peripheral registers and the SRAM are mapped to a bit-
band region, so that single bit-band write and read operations are allowed. The operations 

Содержание STM32F405




































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для STM32F405

VAT 168 Series Installation, Operating, & Maintenance Instructions preview
168 Series
Бренд: VAT Страницы: 29
Balboa Instruments Dolphin Manual preview
Dolphin
Бренд: Balboa Instruments Страницы: 19
Baccara G75-DFC Installation Operation & Maintenance preview
G75-DFC
Бренд: Baccara Страницы: 16
BABYSTYLE OYSTER Instruction Manual preview
OYSTER
Бренд: BABYSTYLE Страницы: 8
BABYSTYLE Hybrid 2 Manual preview
Hybrid 2
Бренд: BABYSTYLE Страницы: 32
Madas M16/RMO NA/NC Installation Instructions Manual preview
M16/RMO NA/NC
Бренд: Madas Страницы: 6
Madas EVP/NC Manual preview
EVP/NC
Бренд: Madas Страницы: 11
R82 Cricket User Guidance preview
Cricket
Бренд: R82 Страницы: 89
York MILLENNIUM Manual preview
MILLENNIUM
Бренд: York Страницы: 20
Water Furnace IntelliZone2 MasterStat Specification Catalog And Design Manual preview
IntelliZone2 MasterStat
Бренд: Water Furnace Страницы: 44
Koer C35CBMS Manual preview
C35CBMS
Бренд: Koer Страницы: 6
V2 WES-EASY Manual preview
WES-EASY
Бренд: V2 Страницы: 48
MaintTech CX300 User Manual preview
CX300
Бренд: MaintTech Страницы: 28
IBA ibaMS16-DI-220V Series Manual preview
ibaMS16-DI-220V Series
Бренд: IBA Страницы: 32
AirCycler SmartExhaust Manual preview
SmartExhaust
Бренд: AirCycler Страницы: 2
TS Performance Torque Converter Lock-Up Manual preview
Torque Converter Lock-Up
Бренд: TS Performance Страницы: 4
Danfoss CHV-X 15-125 Installation Manual preview
CHV-X 15-125
Бренд: Danfoss Страницы: 8
Harman FG2106-04 Quick Start Manual preview
FG2106-04
Бренд: Harman Страницы: 2

Бренды по названию

Популярные бренды

Загрузить еще бренды