manualshive.com logo in svg

STMicroelectronics SPEAr300, Справочное руководство


Поделиться
Скачать
background image

RM0082

RS_SDIO controller

Doc ID 018672 Rev 1

733/844

         

32.7.34 SLTIRQSTS 

register

The SLTIRQSTS bit assignments are given in 

Table 660

.

         

32.7.35 HCTRLVER 

register

The HCTRLVER bit assignments are given in 

Table 661

.

         

Table 659.

SPIIRQSUPP register bit assignments

Bit

Name

Reset 
value

Type

Description

[07:00]

SPIIRQSUPP 8’h00

RW

This bit is set to indicate the assertion of interrupts 
in the SPI mode at any time, irrespective of the 
status of the card select (CS) line. If this bit is zero, 
then SDIO card can only assert the interrupt line in 
the SPI mode when the CS line is asserted.

Table 660.

SLTIRQSTS register bit assignments

Bit

Name

Reset 
value

Type

Description

[15:08]

-

-

Rsvd

Reserved

[07:00]

SLTIRQSIG

8’h00

ROC

These status bit indicate the logical OR of Interrupt
signal and Wakeup signal for each slot. A maximum
of 8 slots can be defined. If one interrupt signal is
associated with multiple slots. the HD can know
which interrupt is generated by reading these status
bits. By a power on reset or by Software Reset For
All, the Interrupt signal shall be de asserted and
this status shall read 00h.

Bit 00 - Slot 1

Bit 01 - Slot 2

Bit 02 - Slot 3

----- -----

Bit 07 - Slot 8

Table 661.

HCTRLVER register bit assignments

Bit

Name

Reset 
value

Type

Description

[15:08]

VVN

8’h69

Hwinit

This status is reserved for the vendor version
number. The HD should not use this status. This
represents Host Controller IP release version.

Содержание SPEAr300













































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SPEAr300

Lattice Semiconductor CrossLink Programming And Configuration Manual preview
CrossLink
Бренд: Lattice Semiconductor Страницы: 30
Garmin TR-1 Gold Installation Instructions preview
TR-1 Gold
Бренд: Garmin Страницы: 4
Maestra 8080 User Manual preview
8080
Бренд: Maestra Страницы: 22
fadini ZERO.SAPE Manual preview
ZERO.SAPE
Бренд: fadini Страницы: 28
Xylem CentriPro Aquavar SOLO Instruction Manual preview
CentriPro Aquavar SOLO
Бренд: Xylem Страницы: 48
Maximum Controls MAX ARM Installation And Owner'S Manual preview
MAX ARM
Бренд: Maximum Controls Страницы: 58
ICP DAS USA XP-9 88-IoT Series Quick Start Manual preview
XP-9 88-IoT Series
Бренд: ICP DAS USA Страницы: 8
SOMFY Situo 1 RTS Manual preview
Situo 1 RTS
Бренд: SOMFY Страницы: 4
Apricus Sentinel S4 Mounting, Connection, Operation preview
Sentinel S4
Бренд: Apricus Страницы: 32
Analog Devices Linear Technology ADI Power DC3017A Demo Manual preview
Linear Technology ADI Power DC3017A
Бренд: Analog Devices Страницы: 12
AUMA VARIOMATIC SARV 07.1 Operation Instructions Manual preview
VARIOMATIC SARV 07.1
Бренд: AUMA Страницы: 32
Industrial Shields M-DUINO PLUS series User Manual preview
M-DUINO PLUS series
Бренд: Industrial Shields Страницы: 46
IFM EC2121 System Manual preview
EC2121
Бренд: IFM Страницы: 41
ADLINK Technology PCIe-8332 User Manual preview
PCIe-8332
Бренд: ADLINK Technology Страницы: 37
Rauch quantron e Operator'S Manual preview
quantron e
Бренд: Rauch Страницы: 85
Texas Instruments CC2530-CC2592EM Quick Start Manual preview
CC2530-CC2592EM
Бренд: Texas Instruments Страницы: 3
Webasto Thermo Call TC3 Installation Instructions Manual preview
Thermo Call TC3
Бренд: Webasto Страницы: 15
Oase StreamMax Pump Controller Operating Instructions Manual preview
StreamMax Pump Controller
Бренд: Oase Страницы: 142

Бренды по названию

Популярные бренды

Загрузить еще бренды