manualshive.com logo in svg

STMicroelectronics SPEAr300, Справочное руководство


Поделиться
Скачать
background image

BS_Serial memory interface

RM0082

306/844

Doc ID 018672 Rev 1

15.8 Programming 

model

15.8.1 External 

pin 

connection

         

The SMI can be fully configured by programming a set of 32 bit wide registers (listed in 

Table 240

) which can be accessed at the base address 0xFC00_0000 

Note:

All transfer to and from these registers must be 32 bit wide only. Any attempt to access with 
a different size will result an ERROR response.

         

15.8.2 Register 

description

15.8.3 SMI_CR1 

register

The SMI_CR1 (control register 1) is a RW register which is able (together with coupled 
SMI_CR2, 

Section 15.8.4

) to configure the behavior of SMI. The SMI_CR1 bit assignments 

are given in 

Table 241

.

         

Table 239.

External pin connection

Signal

Ball

SMI_DATAIN

M13

SMI_DATAOUT

M14

SMI_CLK

N17

SMI_CS_0

M15

SMI_CS_1

M16

Table 240.

SMI registers summary

Name

Offset

Reset value

Description

SMI_CR1

0x000

32’h51

SMI control register 1.

SMI_CR2

0x004

32’h0

SMI control register 2.

SMI_SR

0x008

32’h0

SMI status register.

SMI_TR

0x00C

32’h0

SMI transmit register.

SMI_RR

0x010

32’h0

SMI receive register.

Table 241.

SMI_CR1 register bit assignments

Bit

Name

Reset 
value

Type

Description

[31:30]

Reserved -

-

Read: undefined. Write: should be zero.

[29]

WBM

1’h0

RW

Write burst mode.

Setting this bit, the write burst mode is enabled and 
selected external memory device remains active after an 
AHB write request. In contrast (bit cleared, default), 
selected memory device is released. 

Содержание SPEAr300













































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SPEAr300

S&C 5800 Series Troubleshooting Manual preview
5800 Series
Бренд: S&C Страницы: 34
Warren Controls 313 Installation, Operation & Maintenance Instructions Manual preview
313
Бренд: Warren Controls Страницы: 16
Danfoss VLT MCD 200 Installation Manual preview
VLT MCD 200
Бренд: Danfoss Страницы: 32
Danfoss VLT AutomationDrive FC 360 Programming Manual preview
VLT AutomationDrive FC 360
Бренд: Danfoss Страницы: 60
Danfoss AMV 110 NL AQT Datasheet preview
AMV 110 NL AQT
Бренд: Danfoss Страницы: 4
Danfoss ECL Comfort 110 Quick Manual preview
ECL Comfort 110
Бренд: Danfoss Страницы: 2
IBM 3746-900 Installation Manual preview
3746-900
Бренд: IBM Страницы: 276
IBM 3745 Series Connection And Integration Manual preview
3745 Series
Бренд: IBM Страницы: 157
L-Acoustics LA8 Product Information preview
LA8
Бренд: L-Acoustics Страницы: 20
I-Tork PDS Series Installation & Operation Manual preview
PDS Series
Бренд: I-Tork Страницы: 15
Kantronics KAM XL Reference Manual preview
KAM XL
Бренд: Kantronics Страницы: 201
Brooks GF100 Series Installation And Operation Manual preview
GF100 Series
Бренд: Brooks Страницы: 68
ISC APECS Operational Instructions preview
APECS
Бренд: ISC Страницы: 20
Daktronics All Sport 1600 Series Operation Manual preview
All Sport 1600 Series
Бренд: Daktronics Страницы: 92
YASKAWA PS-V10M Installation Manual preview
PS-V10M
Бренд: YASKAWA Страницы: 38
Danfoss MCI 50-3 I-O Instructions preview
MCI 50-3 I-O
Бренд: Danfoss Страницы: 2
StudioComm 760-03 User Manual preview
760-03
Бренд: StudioComm Страницы: 55
ZiLOG S3F8S19 User Manual preview
S3F8S19
Бренд: ZiLOG Страницы: 23

Бренды по названию

Популярные бренды

Загрузить еще бренды