manualshive.com logo in svg

STMicroelectronics RM0365, Справочное руководство


Поделиться
Скачать
background image

Analog-to-digital converters (ADC)

RM0365

355/1080

DocID025202 Rev 7

15.4 ADC 

interrupts

For each ADC, an interrupt can be generated:

•

After ADC power-up, when the ADC is ready (flag ADRDY)

•

On the end of any conversion for regular groups (flag EOC)

•

On the end of a sequence of conversion for regular groups (flag EOS)

•

On the end of any conversion for injected groups (flag JEOC)

•

On the end of a sequence of conversion for injected groups (flag JEOS)

•

When an analog watchdog detection occurs (flag AWD1, AWD2 and AWD3)

•

When the end of sampling phase occurs (flag EOSMP)

•

When the data overrun occurs (flag OVR)

•

When the injected sequence context queue overflows (flag JQOVF)

Separate interrupt enable bits are available for flexibility.

         

Table 94. ADC interrupts per each ADC

Interrupt event

Event flag

Enable control bit

ADC ready

ADRDY

ADRDYIE

End of conversion of a regular group

EOC

EOCIE

End of sequence of conversions of a regular group

EOS

EOSIE

End of conversion of a injected group

JEOC

JEOCIE

End of sequence of conversions of an injected group

JEOS

JEOSIE

Analog watchdog 1 status bit is set

AWD1

AWD1IE

Analog watchdog 2 status bit is set

AWD2

AWD2IE

Analog watchdog 3 status bit is set

AWD3

AWD3IE

End of sampling phase

EOSMP

EOSMPIE

Overrun

OVR

OVRIE

Injected context queue overflows

JQOVF

JQOVFIE

Содержание RM0365

























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для RM0365

IBM System x3630 M4 Manual preview
System x3630 M4
Бренд: IBM Страницы: 7
Palm M505 Setting Up preview
M505
Бренд: Palm Страницы: 4
Lab.gruppen NLB 60E Operation Manual preview
NLB 60E
Бренд: Lab.gruppen Страницы: 35
Delta M125HV-113 Quick Installation Manual preview
M125HV-113
Бренд: Delta Страницы: 2
UNA AUTOMATION DIFRA Installation Manual preview
DIFRA
Бренд: UNA AUTOMATION Страницы: 20
Rabbit RabbitCore RCM4400W Product Manual preview
RabbitCore RCM4400W
Бренд: Rabbit Страницы: 126
Bridgeworks Oresund EFC102200 User Manual preview
Oresund EFC102200
Бренд: Bridgeworks Страницы: 84
Tandy 26-3814 Operation Manual preview
26-3814
Бренд: Tandy Страницы: 24
AMD Geode LE-366 User Manual preview
Geode LE-366
Бренд: AMD Страницы: 45
Hauppauge WinTV-DVB Installation And Reference Manual preview
WinTV-DVB
Бренд: Hauppauge Страницы: 62
DPS Telecom D-PK-NG432 User Manual preview
D-PK-NG432
Бренд: DPS Telecom Страницы: 80
Zonet ZEN3320E Quick Installation Manual preview
ZEN3320E
Бренд: Zonet Страницы: 1
IceManCooler ICE-SKY-E User Manual preview
ICE-SKY-E
Бренд: IceManCooler Страницы: 2
IBM SA23-1325-01 Installation And Using Manual preview
SA23-1325-01
Бренд: IBM Страницы: 44
Ezquest Boa K16766 User Manual preview
Boa K16766
Бренд: Ezquest Страницы: 65
FabiaTech FB2701 User Manual preview
FB2701
Бренд: FabiaTech Страницы: 86
CoolShirt IB-400 Operating Instructions preview
IB-400
Бренд: CoolShirt Страницы: 3
National Instruments GPIB-120A User Manual preview
GPIB-120A
Бренд: National Instruments Страницы: 36

Бренды по названию

Популярные бренды

Загрузить еще бренды