manualshive.com logo in svg

STMicroelectronics RM0365, Справочное руководство


Поделиться
Скачать
background image

Debug support (DBG)

RM0365

1049/1080

DocID025202 Rev 7

IDCODE read or CTRL/STAT read or ABORT write which are accepted even if the write 
buffer is full.

•

Because of the asynchronous clock domains SWCLK and HCLK, two extra SWCLK 
cycles are needed after a write transaction (after the parity bit) to make the write 
effective internally. These cycles should be applied while driving the line low (IDLE 
state)
This is particularly important when writing the CTRL/STAT for a power-up request. If the 
next transaction (requiring a power-up) occurs immediately, it will fail.

33.8.5 SW-DP 

registers

Access to these registers are initiated when APnDP=0

         

Table 188. SW-DP registers

A(3:2)

R/W

CTRLSEL bit 

of SELECT 

register

Register

Notes

00

Read

-

IDCODE

The manufacturer code is not set to ST code 

0x2BA01477 

(identifies the SW-DP)

00

Write

-

ABORT

-

01

Read/Write

0

DP-
CTRL/STAT

Purpose is to:
– request a system or debug power-up
– configure the transfer operation for AP 

accesses

– control the pushed compare and pushed 

verify operations.

– read some status flags (overrun, power-

up acknowledges)

01

Read/Write

1

WIRE 
CONTROL

Purpose is to configure the physical serial 
port protocol (like the duration of the 
turnaround time)

10

Read

-

READ 
RESEND

Enables recovery of the read data from a 
corrupted debugger transfer, without 
repeating the original AP transfer.

10

Write

-

SELECT

The purpose is to select the current access 
port and the active 4-words register window

11

Read/Write

-

READ 
BUFFER

This read buffer is useful because AP 
accesses are posted (the result of a read AP 
request is available on the next AP 
transaction).
This read buffer captures data from the AP, 
presented as the result of a previous read, 
without initiating a new transaction

Содержание RM0365

























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для RM0365

Acqiris SA217P Startup Manual preview
SA217P
Бренд: Acqiris Страницы: 22
Lucent Technologies PARTNER Voice Messaging PC Card Release 2 Installation And Programming preview
PARTNER Voice Messaging PC Card Release 2
Бренд: Lucent Technologies Страницы: 67
Waves MaxxBCL Manual preview
MaxxBCL
Бренд: Waves Страницы: 41
STMicroelectronics ST62GP-EMU2 HDS2 Series User Manual preview
ST62GP-EMU2 HDS2 Series
Бренд: STMicroelectronics Страницы: 58
ekwb 3831109826140 User Manual preview
3831109826140
Бренд: ekwb Страницы: 11
JETWAY I848ASR1A User Manual preview
I848ASR1A
Бренд: JETWAY Страницы: 47
AC Infinity AIRCOM Series User Manual preview
AIRCOM Series
Бренд: AC Infinity Страницы: 24
Dave Embedded Systems diDo Hardware Manual preview
diDo
Бренд: Dave Embedded Systems Страницы: 79
ADTRAN DUAL Nx56/64 1200142L1# User Manual preview
DUAL Nx56/64 1200142L1#
Бренд: ADTRAN Страницы: 48
Ceragon Fibe-Air IP-10G Installation Manual preview
Fibe-Air IP-10G
Бренд: Ceragon Страницы: 71
Enterasys GPIM-08 Reference Sheet preview
GPIM-08
Бренд: Enterasys Страницы: 2
El.Mo 090010932 User Manual preview
090010932
Бренд: El.Mo Страницы: 16
IBASE Technology SI-22-415 User Manual preview
SI-22-415
Бренд: IBASE Technology Страницы: 49
Arctic Freezer i32 Welcome Manual preview
Freezer i32
Бренд: Arctic Страницы: 7
Alphacool NexXxoS GPX-N 970 M03 Instruction Manual preview
NexXxoS GPX-N 970 M03
Бренд: Alphacool Страницы: 2
Quantum MC300 Prism User Manual preview
MC300 Prism
Бренд: Quantum Страницы: 140
Ametek Land System 4 Landmark Technic Processor User Manual preview
System 4 Landmark Technic Processor
Бренд: Ametek Land Страницы: 34
ESD C.2044.04 Hardware Manual preview
C.2044.04
Бренд: ESD Страницы: 30

Бренды по названию

Популярные бренды

Загрузить еще бренды