
Packaging
During delivery of the truck, certain parts are
packaged to provide protection during trans-
port. This packaging must be removed com-
pletely prior to initial start-up.
ENVIRONMENT NOTE
The packaging material must be disposed of
properly after delivery of the truck.
Emissions
The values specified apply to a standard truck
(compare the specifications in the "VDI data-
sheet" chapter). Different tyres, lift masts, ad-
ditional units etc. may produce different val-
ues.
Noise emissions
The values were determined based on meas-
uring procedures from the standard EN 12053
"Safety of industrial trucks. Test methods for
measuring noise emissions“ based on
EN12001 and EN ISO 3744 and the require-
ments of EN ISO 4871.
This machine emits the following sound pres-
sure level:
Continuous sound pressure level in the driv-
er’s compartment
LpAZ
Measurement
uncertainty KpA
RCD30
83.4 dB
4 dB
The values were determined in the test cycle
on an identical machine from the weighted val-
ues for operating statuses and idling.
However, the indicated noise levels at the
truck cannot be used to determine the noise
emissions at workplaces according to the
most recent version of Directive 2003/10/EC
(daily personal noise pollution). If required,
these noise emissions must be determined di-
rectly at the workplaces under the actual con-
ditions present (further sources of noise, par-
ticular application conditions, sound reflec-
tions) by the operating company.
NOTE
Please note the definition of "operating com-
pany" in the sense of responsible persons!
Vibrations
The vibrations of the machine have been de-
termined on an identical machine in accord-
ance with the standards DIN EN 13059 "Safe-
ty of industrial trucks - Test methods for meas-
uring vibration" and DIN EN 12096 "Mechani-
cal vibration - Declaration and verification of
vibration emission values".
Frequency-weighted effective value of accel-
eration on the seat
The following value is valid for all truck mod-
els:
Driver’s seat Measurement
uncertainty
RCD30
1.272 m/s2
0.3 m/s2
Tests have indicated that the amplitude of the
hand and arm vibrations on the steering wheel
or the operating devices in trucks is less than
2.5 m/s2. There are therefore no measure-
ment guidelines for these measurements.
Safety
2
Emissions
22
60068011601 EN - 09/2020
Содержание RCD25
