Still FS-X33 Скачать руководство пользователя страница 70

Страница: 70 / 94

Maintenance

Lubricants

Only regular maintenance work will enable

you to make full use of the warranty.

Lubricants

CAUTION

Risk of damage to property
Trucks for cold store operation must be lubricated

with different lubricants. Refer to the operating

instructions for cold store trucks.

The following lubricants must be used:
Hydraulic system
• HLP DIN 51524/T2
• ID no. 8 036 912

NOTE

The top-up point for hydraulic oil is marked

with the symbol (1). The hydraulic power unit

can be accessed once the fork rear wall cover

has been removed.

Gearbox
• Oil quality must correspond to at least

GL5/MIL-L-2105 C/D.

• ID no. 8 034 186
Grease lubrication points
• ESSO Beacon 2 multi-purpose grease
• ID no. 8 010 107
Chain lubrication
• Stabylan 2100
• ID no. 8 010 100

Lubrication schedule

every 1,000 hours or every 6 months
• Lubricate the steering gears with all-

purpose grease.

• Lubricate all moving parts with oil.
• Keep sliding surfaces of the mast sections

free of corrosion with a ﬁlm of grease.

• Carry out the ﬁrst gear oil change and then

every 24 months or every 4,000 hours.

51328042507 [EN]

Содержание FS-X33































































































Результаты поиска

Содержание FS-X33

Отзывы:

Похожие инструкции для FS-X33

Бренды по названию

Популярные бренды

Still FS-X33, Оригинальное руководство пользователя

Результаты поиска

Содержание FS-X33

Отзывы:

Похожие инструкции для FS-X33

Бренды по названию

Популярные бренды