
EN
NO
39
SV
FI
DA
PL
0478 192 9810 A - EN
Allow the retaining ring (2) to engage in the
groove on the wheel axle.
Fit the cap (1) onto the wheel axle.
●
Lift the machine and pull out the
support.
●
Carefully set the machine onto the
ground.
14.11 Lubrication
Lubricate the two front steering knuckles
via the two grease nipples on the front
axle.
Lubricating:
●
●
Remove the ignition key and keep it in a
safe place.
●
●
Unload the front axle by supporting
(lifting) it. (
Using a grease gun (not included in
standard equipment), inject grease on
both sides via grease nipples (1) until
small amounts of grease escape from the
steering knuckles.
●
Remove escaping lubricating grease.
●
Remove support for the front axle.
14.12 Checking the engine oil filling
level
●
Park the machine on a flat, level
surface.
●
●
●
Allow the engine to cool down.
●
●
Check the filling level as per the engine
instruction manual – top up the engine
oil if necessary. (
14.13 Changing the engine oil
Information regarding the specified engine
oil and oil capacity can be found in the
engine instruction manual.
Perform an oil change when the engine is
warm to the touch. Place a suitable oil
collection container (note engine oil
capacity) under the oil drain tube.
Dispose of used oil in conformance with
statutory requirements.
Oil change interval:
The recommended oil change intervals
can be found in the engine instruction
manual.
Draining the engine oil:
●
Stop the engine. (
●
Engage the parking brake. (
●
Remove the ignition key and keep it in a
safe place.
●
Allow the engine to cool down (warm to
the touch).
●
Open the engine hood. (
●
Unscrew the oil cap (see engine
instruction manual).
Check that the wheel is seated
securely.
Note
Before lubricating, the front axle
must be unloaded by supporting
appropriately.
The grease nipple must be cleaned
before lubricating, so that no dirt
enters the steering knuckle.
Escaping grease should always be
removed (wiped off) after
lubricating.
Use commercially available
lubricating grease.
Risk of injury!
Allow the engine to cool down
before topping up the engine oil or
before changing the oil.
Danger of burns due to hot engine
oil.
Содержание RT 4097 S
