Stihl MSE 250 C Скачать руководство пользователя | Manualshive

Страница: 16 / 36

background image

2

1

9913BA002 KN

► Turn the tensioning screw (1) counterclock‐

wise until the tensioner slide (2) butts against

the left end of the housing slot.

6.2

Disengaging the Chain Brake

9931BA015 KN

► Pull the hand guard towards the front handle

until there is an audible click – the chain brake

is disengaged.

6.3

Fitting the Chain

WARNING

Wear work gloves to protect your hands from the

sharp cutters.

143BA003 KN

► Fit the chain – start at the bar nose.

4

2

2

3

1

9913BA003 KN

► Turn the guide bar so that the chain is posi‐

tioned as shown in the pictogram (1) – the

arrows show the chain's direction of rotation.

► Fit the guide bar over the studs (2) and

engage the tensioner slide in the hole (3) –

place the chain over the sprocket (4) at the

same time.

5

9913BA004 KN

► Turn the tensioning screw (5) clockwise until

there is very little chain sag on the underside

of the bar – and the drive link tangs are

engaged in the bar groove.

► Refit the sprocket cover and tighten the nut

only moderately by hand – finally tighten the

nut only after tensioning the saw chain.

► Go to chapter on "Tensioning the Saw Chain".

7

Tensioning the Saw Chain

(side chain tensioner)

9913BA005 KN

1

Re-tensioning during cutting work:

► Disconnect the plug from the wall outlet.

► Loosen the nut.

English

7 Tensioning the Saw Chain (side chain tensioner)

16

0458-764-0121-B

«
...
14
15
16
17
18
...
»

Содержание MSE 250 C





































Отзывы:

Нет отзывов

Похожие инструкции для MSE 250 C

Бренд: Delta Страницы: 17

Бренд: Racing Страницы: 32

Бренд: Palmgren Страницы: 32

Бренд: YATO Страницы: 96

Бренд: Yard force Страницы: 17

CS-502HD Series

Бренд: Euro Shatal Страницы: 21

Бренд: Carbatec Страницы: 35

Бренд: Draper Страницы: 20

Бренд: Texas Equipment Страницы: 24

Бренд: Scheppach Страницы: 89

Бренд: Scheppach Страницы: 40

Бренд: Scheppach Страницы: 124

Бренд: Scheppach Страницы: 140

Бренд: Scheppach Страницы: 104

Бренд: Scheppach Страницы: 84

Бренд: Scheppach Страницы: 232

Бренд: Texas Equipment Страницы: 24

Бренд: Milwaukee Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды