background image

3

3

4

2

3

1

0000-GXX-A376-A0

► Remove the filter cover (1).

► Pull off the spark plug boot (2).

► Turn the shroud locks (3) counterclockwise

until the cover (4) can be removed.

► Remove cover (4).

► Remove the chain sprocket cover.

► Use a soft brush, damp cloth or STIHL resin

solvent to clean the chain sprocket cover, cyl‐

inder fins and the inside of the cover and filter

cover.

► Clean the area around the chain sprocket with

a damp cloth or STIHL resin solvent.

► Fit the cover (4).

► Turn the shroud locks (3) clockwise and

tighten them firmly.

The cover (4) is closed.

► Press the spark plug boot (2) firmly home.

► Fit the filter cover (1).

► Fit the chain sprocket cover.

15.2

Cleaning the Bar and Chain

► Shut off the engine and engage the chain

brake.

► Remove the bar and chain.

1

2

0000-GXX-2951-A0

3

3

► Clean the oil port (1), oil inlet hole (2) and bar

groove (3) with a soft brush or STIHL resin

solvent.

► Clean the saw chain with a soft brush or

STIHL resin solvent.

► Mount the bar and chain.

15.3

Cleaning the Air Filter

Very fine dust can collect in the air filter. The

dust can clog the filter and cannot be removed

by brushing or knocking out. The air filter must

be cleaned with a cleaning agent.

► Shut off the engine and engage the chain

brake.

► Press the throttle trigger lockout and keep

pressed.

► Press the throttle trigger and keep pressed.

► Move the Master Control Lever to position  .

► Release the throttle trigger and throttle trigger

lockout.

1

3

2

0000-GXX-A377-A0

► Turn the filter cover lock (1) counterclockwise

until the filter cover (2) can be removed.

► Remove filter cover (2).

► Clean the area around the air filter (3) with a

damp cloth or a soft brush.

► Remove the air filter (3).

► Rinse away coarse dirt from the outside of the

air filter (3) under running water.

► If the air filter (3) is damaged: Install a new air

filter (3).

WARNING

■ If detergents come into contact with the skin or

eyes, the skin or eyes may be irritated.

► Observe the user manual for the detergent.

► Avoid contact with detergents.

► If skin contact occurs: Wash affected areas

of skin with plenty of water and soap.

► If eye contact occurs: Flush eyes with plenty

of water for at least 15 minutes and consult a

doctor.

► Spray the outside and inside of the air filter

(3) with STIHL special cleaner or a cleaning

agent with a pH value higher than 12.

► Allow STIHL special cleaner or cleaning agent

to act for 10 minutes.

► Use a soft brush to clean the outside of the air

filter (3).

► Rinse the outside and inside of the air filter (3)

under running water.

► Allow the air filter (3) to dry in the air.

English

15 Cleaning

24

0458-890-8321-B. VA0.A21.

Содержание MS 881

































Отзывы: