Stihl FS 87 Скачать руководство пользователя страница 19

Страница: 19 / 48

FS 87, FS 87 R

English

Preparations

Lay your brushcutter on its back so

that the cutting attachment

mounting face is facing up.

Mounting hardware for cutting

attachments

The mounting hardware supplied

depends on the cutting attachment that

comes as original equipment with the

new machine.

Mounting hardware is not packed with

machine
Only mowing heads can be mounted.

Pull the hose (1) (protector for

shipping) off the shaft (2).

Go to "Mounting the mowing head".

If you want to mount a metal cutting

attachment in place of a mowing head,

you will need the following additional

parts: Nut (3), rider plate (4) and thrust

washer (5) (special accessories).

Mounting hardware is packed with

machine
Mowing heads and metal cutting

attachments may be mounted.

If the parts are packed with the machine

Pull the hose (1) (protector for

shipping) off the shaft (2).

The nut (3), rider plate (4) and thrust

wsher (5) are in the parts kit supplied

with the machine.

Go to "Mounting the mowing head"

or "Mounting the metal cutting

attachment".

If the parts are mounted to the gearbox

Go to "Removing the mounting

hardware".

Removing the mounting hardware

Block the shaft – see next chapter

on "Blocking the output shaft".

Use the combination wrench (6) –

comes standard with machine or is

available as special accessory – to

unscrew the nut (3) clockwise (left-

hand thread) from the shaft (2).

Pull the thrust washer (5) off the

shaft (2).

The rider plate (4) is in the parts kit

supplied with the machine.

Mounting the Cutting

Attachment

002BA104 KN

002BA164 KN

Содержание FS 87

















































Результаты поиска

Содержание FS 87

Отзывы:

Бренды по названию

Популярные бренды

Stihl FS 87, Инструкция по эксплуатации

Результаты поиска

Содержание FS 87

Отзывы:

Бренды по названию

Популярные бренды