Stiga PARK PRO 16, Инструкция по эксплуатации

Страница: 10 / 19

66
ENGLISH EN
2.4.9 Ignition lock/headlight (4,5:I)
The ignition lock is used for starting and stopping
the engine. The ignition lock is also the switch for
the headlight.
Do not leave the machine with the key
in position 2 or 3. There is a fire risk,
fuel can run into the engine through the
carburettor, and there is a risk of the
battery being discharged and damaged.
Four positions:
1. Stop position – the engine is short-cir-
cuited. The key can be removed.
2. Operating position – headlight activat-
ed.
3. Operating position – headlight not acti-
vated.
4. Start position – the electric start motor
is activated when the key is turned to the
spring-loaded start position. Once the en-
gine has started, let the key return to oper-
ating position 3.
Turn the key to position 2 to light the
headlight.
2.4.10 Power take-off (4,5:K)
Switch for engaging/disengaging the electromag-
netic power take-off for operating front-mounted
accessories. Two positions:
1. Press the front part of the switch – the
power take-off is engaged. The symbol
will light up.
2. Press the rear part of the switch – the
power take-off is disengaged.
2.4.11 Hour meter (2:P)
Indicates the number of working hours. Only
works when the engine is running.
2.4.12 Cruise control (5, 6:N)
A switch for activating the cruise control. The
cruise control locks the pedal (3:F) in the desired
position.
1. Press down the pedal (3:F) until the de-
sired speed is obtained. Then press the
front part of the switch to activate the
cruise control. The symbol will light up.
2. Disengage the cruise control by releas-
ing it with the pedal (3:B) or pressing the
rear part of the switch.
2.4.13 Cutting height adjustment (4,5:J)
The machine is equipped with a control for using
the cutting deck with electrical cutting height ad-
justment.
The switch is used to adjust the cutting
height in continuously variable positions.
The cutting deck is connected to the contact (2:Q).
2.4.14Rear Rake (5:L)
(Pro20, Pro25, Pro Svan)
The machine is fitted with a control for electrical
adjustment of a rear rake (available as an
accessory).
The switch is used to raise and lower the
rear rake.
Cables for connecting the rear rake are found at the
rear of the machine, to the left of the upper side of
the bumper.
2.4.15 Sand spreader (6:O)
(Pro20, Pro25, Pro Svan)
The machine has been designed for electrical ad-
justment of a sand spreader (accessory).
The switch is used to start and stop the
spreader.
Cables for connecting the sand spreader are at the
rear of the machine.
2.4.16 Clutch release lever (6:R)
A lever for disengaging the variable transmission.
Enables the machine to be moved by hand without
the help of the engine.
The disengagement lever must never be
between the outer and inner positions.
This overheats and damages the trans-
mission.
Two positions:
1. Lever out – transmission en-
gaged for normal operation.
There is an audible click when
the lever locks in the outer posi-
tion.
2. Lever in – transmission disen-
gaged. The machine can be
moved by hand.
The machine may not be towed over long distances
or at high speeds. The transmission could be dam-
aged.
2.4.17 Seat (1:T)
The seat can be folded and adjusted front-
rear. The seat can be adjusted as follows:
1. Move the control lever (1:T) upwards.
2. Set the seat to the desired position.
12V