Stiga PARK 120 2016 Скачать руководство пользователя страница 66

Страница: 66 / 74

Edition

2016

Workshop Manual

PARK 120 - PARK 220

Chapter

8 Mower Decks

Page

Table of contents
8.1 Original blades .....................................................................................................67

8.1.7 Why it is so important to use original blades and blade tips from the retail deal-

er? 67

8.2 Replacement of blades ........................................................................................68

8.2.1 Disassembly ..................................................................................................68

8.2.2 Assembly .......................................................................................................68

8.3 Replacement of belt .............................................................................................69

8.3.1 Disassembly ..................................................................................................69

8.3.2 Checks ...........................................................................................................70

8.3.3 Assembly of belt ............................................................................................70

8.4 Replacements of the hub ....................................................................................71

8.4.1 Disassembly ..................................................................................................71

8.5 Synchronising, blades .........................................................................................72

8.6 Replacement of the cylinder / engine lifting ......................................................73

8.7 Replacement of the spring of the lift lever manual ...........................................73

General description

The deck are equipped with two synchronised rotating blades. The tracks of adjacent

blades are overlapping each other, which means that the synchronization is vital.

All shafts/pulleys are pivoted in sealed and permanent lubricated ball bearings.

All decks are provided with a quick-coupling to simplify the lifting up procedure for cleaning

and inspection and. The decks are also provided with an electrical or manual adjusting

device for the cutting height.

All decks are tested prior to delivery and are delivered as completely assembled as

possible. This ensures that assembly on delivery is rapid and simple.

This chapter describes how to repair and adjust the cutting device assembly.

For information on how to install it on the main machine and for information on periodical

maintenance and cleaning operations, please refer to the INSTRUCTION MANUAL.

Safety

To reduce the risk of accidental injury in the event of a collision and to protect important

parts in the cutting deck, a force limiter is integrated as follows.

• Shear bolts between blades and blade bar.

• Torque limiting between gear wheels and blade shaft.

• Possibility of positive drive belt slipping on the plastic gear wheels.

8 Mower Decks

Содержание PARK 120 2016











































































Результаты поиска

Содержание PARK 120 2016

Отзывы:

Похожие инструкции для PARK 120 2016

Бренды по названию

Популярные бренды

Stiga PARK 120 2016, Руководство по ремонту

Результаты поиска

Содержание PARK 120 2016

Отзывы:

Похожие инструкции для PARK 120 2016

Бренды по названию

Популярные бренды