background image

3

    PARTS LIST 

Resistor values are indicated by color bands, read from left to right. 
The first color in the code is usually the one painted closer to a lead wire. 
See more about resistor color codes on page 5.

470Ω resistor (1)

 

#7355

 

15K resistor (1) 

#7378

 

4.7K resistor (2) 

#7359

 

1.8K resistor (1)

 

#7384 

22K resistor (2) 

#7379

 

2.2K resistor (1)

 

#7376

 

3.3K resistor (1) 

#7377

 

33K resistor (1) 

#7409

47K resistor (2) 

#7369

82K resistor (1) 

#7410

100K resistor (1) 

#7365 

133K resistor (1) 

#7414

215K resistor (1) 

#7416

 

232K resistor (1) 

#7417

330K resistor (1) 

#7418

1.5M resistor

 

(1) 

#7425 

10pF capacitor (1) 

#7526

6.8nF capacitor (1) 

#7474

120pF capacitor (1) 

#7472

100

IIC

121

1nF capacitor (1) 

#7302

102J

1N5817 rectifier diode (1)

#7522

2N5088 transistor (3) 

#7513

2N508

8

2N5087 transistor (1) 

#7512

2N5087

82nF capacitor (1)

 

#7525

823

47Ω resistor (1)

 

#7351

Yellow   Violet   Black   Gold   Brown

Yellow   Violet   Black   Black   Brown

Brown   Gray   Black   Brown   Brown

Red   Red   Black   Brown   Brown

Red   Red   Black   Red   Brown

Orange   Orange   Black   Red   Brown

Yellow   Violet   Black   Red   Brown

Gray   Red   Black   Red   Brown

Orange   Orange   Black   Brown   Brown

Yellow   Violet   Black   Brown   Brown

Brown   Black   Black   Orange   Brown

Brown   Orange   Orange   Orange   Brown

Red   Brown   Green   Orange   Brown

Red   Orange   Red   Orange   Brown

Orange   Orange   Black   Orange   Brown

Brown   Green   Black   Yellow   Brown

Brown   Green   Black   Red   Brown

Содержание EC EXPANDER PEDAL KIT

















Отзывы: