Stewart Audio CVA50-1 Priority PA Скачать руководство пользователя страница 11

20 

4  Troubleshooting 

 

Problem: Power indicator does not turn on. 

 
Procedure: 

Check that the amplifier is plugged into a live outlet. After 

you have ensured that it is not a power issue, disconnect any speakers. 
If the amplifier turns on after a few seconds delay, then the problem is 
in the output connection. Check wiring and speakers for short circuits.   
 
 

Problem: No output on one or both channels; Power indicator is 
lit. 

 
Procedure: 

Check that level controls are  not turned down. Check that 

input and output connections are secure. Refer to 

section 2.5 

to en-

sure that you have properly connected your speakers. Ensure signal 
present LED is flashing to denote a signal. If there is no signal detected 
check signal source and that level controls are set high enough. 
 
 

Problem: Microphone level is too low even after adjusting level 
knob

 

 

Procedure: 

Refer to 

section 3.2.2 

to adjust the gain switch on the rear 

of the amplifier. 
 
 

Problem: Channels 2-4 cut out while speaking into the microphone 

 

Procedure: 

This is part of an intended feature calling ducking. Refer to 

section 3.2.4

 to adjust this to a more acceptable level. 

 
 

Problem

Amplifier overheats and/or shuts off.

 

 

Procedure: 

Review 

section 2.3

 on proper cooling procedures. Check 

the signal lights on the front of the amplifier to see if the signal is over-
driving (the Clip light flashes red frequently). Overdriving the amplifier 
for extended periods of time can cause a thermal shutdown.

 

21 

4  Troubleshooting (Cont.) 

 

Problem: Output sound is distorted or cracking. 

 
Procedure: 

Check all cables for damage or loose connections and re-

duce the gain on the input signal at the mixer or preamp level. Replace 
the cables and loudspeakers temporarily to see if this resolves the 
problem. If problem still exists, contact your Authorized Dealer for ser-
vice. 

Содержание CVA50-1 Priority PA















Отзывы: