background image

Table of Contents 

 
 

 
 
 
SAFETY AND EQUIPMENT PROTECTION ………………………… 3 
 
1 INTRODUCTION ........................................................................... 5 

1.1 GENERAL DESCRIPTION .................................................... 5  
1.2 SAFETY INFORMATION ......................................................  6  
1.3 FLOAT WELLS AND INSTRUMENT SHELTERS ................  6  
1.4 TYPE A/F ENCODER SPECIFICATIONS ............................  6  

 

2 INSTALLATION ............................................................................  8  

2.1 Type A/F Encoder, standalone .............................................  8  
2.2 Type A/F Encoder on Type A Recorder.................................  9  
2.3 Type A/F Encoder on Type F Recorder ................................  10  
2.4 Electrical Installation .............................................................  11 

 

3. MAINTENANCE AND TROUBLESHOOTING ............................  12 

 

3.1 MAINTENANCE ...................................................................  12  
3.2 TROUBLESHOOTING CHART ............................................  12 
3.3 FACTORY ASSISTANCE .....................................................  12

 

 

LIST OF ILLUSTRATIONS 

Figure 1.  Standalone A/F Encoder ............................................. 8 
Figure 2. Installation on the Type A Recorder ............................. 9 
Figure 3. Installation on the Type F Recorder .............................  10  

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

 

 

2

Содержание 44903













Отзывы: